1) hot rolled plate
热轧钢板
1.
Numerical simulation analysis of effects of jet angle on hot rolled plate cooling;
雾化喷射角度对热轧钢板冷却影响的模拟分析
2.
The width of laser welds on the top and bottom surfaces of hot rolled plates after laser welding was measured.
测量了激光对接焊后热轧钢板正背表面焊缝宽度,分析了激光焊的焊接速度对热轧钢板焊缝成形和质量的影响。
3.
The flatness quality problems,such as sidewise bending and wraping usually appear in hot rolled plate products.
针对热轧钢板产品常出现的旁弯、翘曲等板形质量问题,通过盲孔法测量钢板矫直前以及粗矫直、精矫直后的残余应力分布来分析矫直工艺对钢板残余应力分布的影响,以便改善热轧钢板产品的质量。
2) hot-rolled steel plate
热轧钢板
1.
The scale on the hot-rolled steel plate with weak texture was analyzed by XRD first,then the obtained XRD patterns were refined by Rietveld whole pattern fitting method with Highscore plus software,and finally the refined results were corrected by preferred orientation correction to realize the quantitative phase composition analysis.
首先对具有弱织构热轧钢板表面的氧化皮进行了X射线衍射(XRD)分析,然后选用Highscore plus软件通过Rietveld全谱拟合方法对得到的XRD谱进行精修,实现了对氧化皮的定量相分析,最后对精修结果进行了择优取向校正,并研究了择优取向校正对拟合结果的影响。
3) hot rolling steel plate
热轧钢板
1.
Through Q235 hot rolling steel plate lamellar fracture macroscopic and microscopic observation analysis,as well as the steel plate microstructure,the non-metallic inclusions examination analysis,verification of the serious microstructure nonuniformity is the reason that causes the Q235 hot rolling steel plate lamination to roll over the crack.
通过对Q235热轧钢板分层断口的宏观和微观观察分析,以及钢板显微组织、非金属夹杂物的检验分析,查明严重的组织不均匀性是导致Q235热轧钢板分层轧裂的原因。
4) hot rolled steel sheet
热轧钢板
1.
In the design of the die for stamping the hot rolled steel sheet, the problem of removing the oxidated scraps on the material surface shall be taken into consideration, by which the service life of the die could be extended.
在热轧钢板的冲模设计时 ,应考虑到其材料表面氧化皮的排屑问题 ,这样可提高模具的寿
5) hot rolled sheet
热轧钢板
1.
The hot rolled sheet used for auto chasis frames was developed by use of low C-Mn-V alloying,wire feeding,secondary steelmaking and controlled rolling techniques at Pangang.
介绍了攀钢汽车大梁用热轧钢板的开发。
6) hot rolled steel plate
热轧钢板
1.
Spray cooling of the hot rolled steel plate was simulated,by using Finite Element Coupling numerical simulation.
利用有限元耦合场数值模拟计算方法对雾化冷却热轧钢板进行了模拟,在固定喷嘴到热轧钢板距离H的情况下,得出喷嘴喷射角度对雾化冷却热轧钢板的影响规律,并对重力作用对雾化冷却的影响进行了研究。
补充资料：1450ram热轧宽带钢精轧机组(攀枝花钢铁公司)
1450ram热轧宽带钢精轧机组(攀枝花钢铁公司)
枝_:轧宽带钢精轧机组(攀哪
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条