2) high temperature strain
高温应变
1.
Development of high temperature strain measuring technique and the measuring system;
高温应变测试方法与测试系统开发
2.
The high temperature strain measurement method was proposed to find out the maximum stress and its distribution.
为找出管道的最大应力及应力分布,提出了用高温应变测量分析方法,对高温压力下的蒸汽管道进行现场应力测试,通过重新合理调整支吊架,大幅降低了管道结构应力并达到延寿的目的,实际验证表明该方法具有良好的降应力效果。
3) high strain rate
高应变率
1.
Study on deformation and failure of TA2 under compressive load at high strain rate;
高应变率下工业纯钛TA2变形与失效研究
2.
Tensile experimental technique for resin matrix fiber-reinforced composites at super-high strain rates;
树脂基纤维增强复合材料超高应变率拉伸研究
3.
Dynamic mechanical behavior of concrete under high strain rate using SHPB;
高应变率下混凝土动态力学性能SHPB实验
4) high strain rates
高应变率
1.
The constitutive relation of an Mg-Al Alloy under uniaxial compression at high strain rates is fitted and checked using the SHPB(Split Hopkinson Pressure Bar)experimental results and the numerical simulation based on the fitted constitutive law of the specimen.
从实验与数值模拟的结合上,确定与考察了镁铝合金在一维应力高应变率压缩状态下的本构关系。
2.
In this paper, the glass-epoxy 3-D braided composites are tested under high strain rates(4000 s -1,5000 s -1,6000 s -1) with SHPB(the split Hopkinson pressure bar)for dynamic response, The experimental results show that the glass-epoxy 3-D braided composites are strain rate sensitive materials.
本文利用SHPB(thesplitHopkinsonpressurebar)装置对玻璃纤维/环氧三维编织复合材料在高应变率(40 0 0s-1,5 0 0 0s-1,6 0 0 0s-1)下的动态压缩性质进行测试,试验结果表明玻纤/环氧三维编织复合材料是应变率敏感材料。
3.
To objectively describe the behavior of confined concrete under high strain rates the loading history has to be taken into account.
客观描述高应变率作用下的约束混凝土的力学行为需要考虑加载历史。
5) high-temperature strain gauge
高温应变计，高温应变仪
6) high temperature strain gauge
高温应变片
1.
Because it has a high working temperature,the high temperature strain gauge is necessary in composing the strain measurement electric-bridge.
由于工作温度较高,所以需采用高温应变片来组成应变测量电桥。
2.
Because of the high temperature,conventional strain gauges are ineffective,so high temperature strain gauges are used,which have weldable stainless-steel backing,and the temperature compensation must be considered.
由于炉壳在工作过程中表面温度较高,无法使用常规的应变片进行测量,所以采用了焊接式不锈钢基底的高温应变片。
补充资料：应变硬化率
strainhardeningrate：表示应变硬化的程度，即表示塑性变形阻力（继续塑性变形所需外应力）随塑性变形量的增大而增加的现象的程度。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条