说明:双击或选中下面任意单词,将显示该词的音标、读音、翻译等;选中中文或多个词,将显示翻译。
您的位置:首页 -> 词典 -> 凝胶模型
1)  jellium model
凝胶模型
1.
The thesis is structured as below:Chapter 1 is a brief introduction to metal cluster as well as Jellium model which describes its electronic structure,mainly introduced the sphere Jellium model.
本论文主要包括以下内容:第一章,对金属团簇以及用于描述其电子结构的凝胶模型的简要介绍,其中主要介绍了球形凝胶模型的计算原理。
2)  Gelcasting
凝胶注模成型
1.
Effects of process parameters on the gelcasting green strength and sintered density of stainless steel;
工艺参数对凝胶注模成型不锈钢坯体强度和烧结密度的影响
2.
The Performance and Microstructure of Green bodies on Gelcasting of Zirconium Ceramic;
凝胶注模成型氧化锆陶瓷坯体的性能和显微结构分析
3.
Effects of several factors on gelcasting of Alumina-(3:1)spinel slurries;
几种因素对刚玉-(3:1)尖晶石体系凝胶注模成型工艺的影响
3)  gel-casting
凝胶注模成型
1.
Influence of MgO and TiO_2 on mechanical properties of zirconia toughened alumina ceramics formed by gel-casting technique
MgO和TiO_2烧结助剂对凝胶注模成型氧化锆增韧氧化铝陶瓷性能的影响
2.
The preparation processing of SiC/carbon black suspension with low viscosity and high solid loading for gel-casting was studied.
研究了碳化硅/炭黑凝胶注模成型中低粘度、高固含量浆料的制备工艺,分析讨论了碳化硅颗粒级配、分散剂、pH值以及有机单体含量对浆料流变性能的影响,成功地制备出固相体积分数为60%,表观粘度为680mPa。
3.
The green bodies of titanium-bioglass composite were prepared by gel-casting process.
采用凝胶注模成型工艺制备了钛-生物玻璃复合材料坯体。
4)  gelatification and polarization model
凝胶极化模型
5)  gel casting
凝胶注模成型
1.
Technological factors in gel casting of Al_2O_3-SiC composite;
Al_2O_3-SiC复相陶瓷凝胶注模成型工艺因素的研究
2.
Nano-SiO_(2)-coated Al_(2)O_(3) micro-composite system was derived from silica sol and αAl_(2)O_(3) to prepare mullite ceramics by gel casting technology.
采用硅溶胶等制备纳米SiO2包覆Al2O3微复合体系,凝胶注模工艺制备莫来石陶瓷,着重研究了低粘度高固含量浓悬浮体系的特性及其凝胶注模成型坯体的性能。
3.
It was described that study on gel casting and sintering of silicon carbide in this paper.
研究了碳化硅耐火材料的凝胶注模成型及其烧结性状 。
6)  corneal stroma model equivalent
三维凝胶模型
补充资料:Sds-聚丙烯酰胺凝胶电泳凝胶电泳

sds-聚丙烯酰胺凝胶电泳(sds-page,sodium dodecyl sulfate-polyacrylamide gel electrohoresis)

在有去污剂十二烷基硫酸钠存在下的聚丙烯酰胺凝胶电泳。sds-page只是按照分子大小分离的,而不是根据分子所带的电荷和大小分离的。

说明:补充资料仅用于学习参考,请勿用于其它任何用途。
参考词条