1) mill temperature
轧线温度
2) finishing rolling temperature
终轧温度
1.
The effect of finishing rolling temperature on banded structure of 16Mn steel plate;
终轧温度对16Mn钢板带状组织的影响
2.
Influence of finishing rolling temperature on microstructure and properties of Q450NQR1 high strength weathering steel
终轧温度对高强度耐候钢Q450NQR1组织和性能的影响
3.
By using controlled rolling and cooling,optical and electron microscopy observation,mechanical test etc,the microstructure of hot-rolled 60Si2CrVAT rolled with different finishing rolling temperature,and the effect of hot rolled structure on the microstructure and properties of heat treated products were studied.
以铁路用弹簧钢60Si2CrVAT为研究对象,通过工业控轧控冷试验,采用光学、电子显微技术和力学分析等方法,系统研究了在不同终轧温度下热轧态的组织结构以及对其热处理后组织性能的影响。
3) final rolling temperature
终轧温度
1.
The effects of final rolling temperature and cooling rate on microstructure at room temperature were studied.
通过Gleeble-1500热模拟机对20CrMo轧材精轧阶段轧制过程及冷却过程的模拟,研究了终轧温度、冷却速度对室温组织的影响,分析了形成带状组织的条件,最终得出了理想室温组织的终轧温度和冷却速度。
2.
Influence of final rolling temperature, cooling rate and tempering on properties of fire-resistant steel was researched.
测定了耐火钢的CCT曲线,研究了耐火钢的性能,包括室温和高温拉伸性能、系列温度下的冲击性能、应变时效性能等;探讨了终轧温度、冷却速度、回火对耐火钢性能的影响。
3.
According to the characteristics of micro-carbon steel,simulative test was taken in laboratory under the principle of "high heating temperature,high beginning rolling temperature,high final rolling temperature and low rolling temperature".
针对微碳钢的特点 ,在实验室进行了模拟试验 ,在“三高一低”的原则下 ,研究了微碳钢加热温度对AlN溶解的影响 ,终轧温度及冷却速度对热轧晶粒度的影响 ,卷取温度对AlN和渗碳体析出的影响。
4) rolling temperature
轧制温度
1.
A model of regulation optimization control for thin gauge strip high-speed rolling of cold tandem mill was established,which was taken the rolling temperature of each stand as the target,and assured coiling temperature and rolling load under restriction.
根据薄带高速冷连轧生产的工艺特点,以各机架轧制温度相对均匀为目标,同时以保证终卷温度在设定范围内和各机架轧制负荷不超限为约束条件,建立了一套冷连轧机高速轧制的轧制规程优化控制模型,使用后效果较好。
2.
Using the mathematic model and the engineering log, the factors affecting the head thickness precision are analyzed and a conclusion that the rolling temperature is the main factor is got.
热轧带钢的厚度精度是产品质量的重要指标 ,文章结合数学模型和工程日志对生产中影响带钢头部厚度的原因进行了分析 ,得出轧制温度是影响厚度的主要原因。
3.
Study is made of the effect of rolling temperature and single-pass deformation rate on Kovar/Cu/Kovar laminates .
分析研究了轧制温度和单道次变形率对Kovar/Cu/Kovar层状复合材料制备的影响。
5) Hot Rolling Temperature
热轧温度
6) Finishing temperature
终轧温度
1.
Influencing factors on finishing temperature of plate rolling;
影响中厚板轧制终轧温度的因素及其控制
2.
A simulation software was developed to research the finishing temperature of hot strip rolling,based on conventional heat transfer model.
在传统传热模型基础上开发了带钢热连轧精轧温度控制模拟软件,系统地分析了穿带速度、带钢粗轧出口温度、带钢机架间厚度、水冷换热系数和工作辊材质等7种因素对带钢精轧出口温度的影响规律;确定了影响带钢终轧温度的主要因素;使用现场实测数据对模拟软件计算精度进行了检验,表明开发的精轧温度控制模拟软件计算精度较高。
3.
The standard deviation between the predicted and measured finishing temperature was reduced by 14.
结果表明,利用BP神经网络得出的带钢热流密度计算的终轧温度与实测值的标准差比原来仅用数学模型的传统算法减少了14 08%,故该方法具有较好的在线应用前景。
补充资料：常州冶炼厂铝线坯连铸连轧生产线
常州冶炼厂铝线坯连铸连轧生产线
常州冶炼厂铝线坯连铸连轧生产线粉
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条