1) Stage by stage adjust the sopping profile

段塞调剖
2) profile modification

调剖
1.
Field test of profile modification on produced sludge in Xingbei Oilfield;

杏北油田采出污泥调剖现场试验研究
2.
Integrated evaluation on reservoir profile modification suitability degree using fuzzy hierarchy determination;
应用模糊层次评判法进行油藏调剖适宜度综合评价
3.
Profile modification and profile modification plus oil displacement technique in the high water cut oilfield in Zhongyuan Oilfield;
中原高含水油田调剖、调驱技术研究
4) profile control

调剖
1.
Percolation performance of suspending profile control agent in reservoir formation;

悬浮液调剖剂在油层中渗滤特征研究
2.
The application of profile control technology before polymer injection in Ng3-4 cell of the north of central region 2 of Gudao Oilfield;
孤岛油田中二北Ng3-4注聚前整体调剖技术应用
3.
Composing of pore-scale polymer microsphere and its application in improving oil recovery by profile control;
孔喉尺度聚合物微球的合成及全程调剖驱油新技术研究
5) profile correction

调剖
1.
In viewing of the characteristics of low porosity and low permeability, well developed micro - fissures and high formation temperature in Baolang oilfield, we selected a strong gel profile correction agent with high temperature tolerance, large strength and good compatibility with the formations.
针对宝浪油田油藏低孔低渗、微裂缝发育及地层温度高的特点,选择了耐温高、高强度、与地层配伍性良好的强凝胶调剖剂;B1306井调剖现场试验表明,调剖后注水启动压力上升,吸水指数下降,注水剖面改善良好,为下步对宝浪油田水窜井的治理打下了基础。
2.
In view of the geological characteristics, a formula for profile correction agent was selected in 2001 through experiments.
2 0 0 1年针对其地层地质特点 ,实验评选出凝胶强度大、热稳定性好、封堵效果大于 80 % ,成胶时间可控的调剖剂配方 ,对三口井实施了调剖 ,有效封堵了水窜通道并取得较好的增油降水效果。
6) slug
[英][slʌɡ] [美][slʌg]

段塞
1.
Physical modeling of ASP flooding slug combination;

三元复合驱注入段塞组合物理模拟实验研究
2.
Evaluation on flow conductivity of mixed proppant caused by slug

段塞导致的混合支撑剂导流能力评价
3.
The flow properties, fractional flow and profile modification effect of polymer solution and micro-gel system were tested, and combination flooding of polymer slug with micro-gel slug were experimented in parallel super-long core and heterogeneous inter-layer models.
使用双管并联长岩心填砂模型和五点法层间非均质模型,模拟研究聚合物溶液和微凝胶体系的流动特征、分流作用和剖面调整能力,探讨微凝胶与低浓度聚合物交替段塞组合的调驱性能和驱油效果,为提高采收率组合驱油方法提供实验依据和理论指导。
补充资料:全面解析在AutoCAD中模型的半剖.全剖.局部剖
在cad如何做些剖切呢.今日写了一个教程,抛砖引玉,希望给大家点思路.随便做了一个模型,下面就来发张图片
图1
图2
用剖切面完全剖开机件所得的剖视图称为全剖视图。全剖视图用于外形简单内部结构较复杂且不对称的机件。
全剖.操作要点:xy,.XZ,YZ等平面的剖面都是依据你的ucs坐标来的,因此如果某些时候剖切得不到全剖效果的话,那就你的坐标系有问题.
图3
最后选择b,保留两侧,得到全剖效果
图4
图5
半剖模型:
当机件具有对称平面时,在垂直于对称平面的投影面上投射所得的图形,以对称中心线为界,一半画成剖视图,另一半画成视图,这种剖视图称为半剖视图。半剖视图适用于内外结构都需要表达且具有对称平面的机件。
画半剖视图应注意:
(1)视图和剖视的分界线应是细点画线,不能以粗实线分界。
(2)半剖视图中由于图形对称,机件的内部形状已在半个剖视图中表示清楚,所以在表达外部形状的半个视图中不画虚线,以及在后方不可见的虚线都不画。
(3)机件的形状接近于对称,且不对称部分已另有图形表达清楚时,也可以画成半剖视图。
(4)当对称机件的轮廓线与中心线重合时,不宜采用半剖视图表示。
半剖的操作与阶梯剖有点相似.只不过阶梯剖的要做多条辅助线
图6
图7
局部剖:
用剖切面局部地剖开机件,以波浪线或双折线为分界线,一部分画成视图以表达外形,其余部分画成剖视图以表达内部结构,这样所得的图形称为局部剖视图。它用于内外结构都需要表达且不对称的机件。
说明:补充资料仅用于学习参考,请勿用于其它任何用途。
参考词条