1) ACR latex
ACR胶乳
1.
The coagulation efficiency of ACR latex was characterized by the variation of particle size during the coagulation process.
以丙烯酸酯(ACR)聚合物胶乳凝聚过程中粒径的变化表征凝聚效果,探讨在凝聚剂作用下的凝聚机理,研究凝聚剂、凝聚温度、搅拌转速、搅拌时间和胶乳固含量等条件对凝聚过程的影响规律,为优化工艺条件,制备大小均匀、形态较为规整的凝聚颗粒,实现ACR胶乳凝聚的工业化提供基础。
2.
The present work investigated the coagulation mechanism and influencing factors of ACR latex based on the fundamental investigation of preparation technology of coagulated particles.
本文在探索凝聚法制备ACR胶乳凝聚颗粒的工艺的基础上，着重研究了胶乳凝聚的机理和影响因素，为ACR胶乳凝聚工业化打下理论和实践基础，也可供其他胶乳的凝聚参考。
2) latex
[英]['leɪteks] [美]['letɛks]
胶乳
1.
Experiment of salt-resisting performance of polyvinyl alcohol latex oil-well cement;
聚乙烯醇胶乳油井水泥抗盐性能实验
2.
Synthesis of large particle polybutyl acrylate latex;
大粒径聚丙烯酸丁酯胶乳的制备
3.
Improvement of latex on mechanical deformation capability of cement sheath under triaxial loading condition;
胶乳对水泥石三轴力学形变能力的作用
3) emulsion
[英][ɪ'mʌlʃn] [美][ɪ'mʌlʃən]
乳胶
1.
The initiator is summarized in grafting copolymerization preparation emulsion with using starch and ethenyl monomer , each kind of initiator mechanism is commented, influence of the initiator selecting to the emulsion performance is elaborated.
总结了淀粉与乙烯基单体接枝共聚制备乳胶常用的引发剂,对各类引发剂的机理作了评述,讨论引发剂的选用对乳胶性能的影响。
2.
The process of manufacturing emulsion products and its capacity indexes have been analyzed in this paper.
本文分析了乳胶制品的生产过程，并对工序能力指数进行了分析，从而推断出产品的质量。
3.
Methods: A random, single blind, positive-control and multi-center clinical trial recruited 230 patients with osteoarthritis, who were randomly applied onto the affected area with either piroxicam patch (n = 116) once every other day or diclofenac emulsion (n = 114) three times per day for 14 days.
方法:研究采用多中心、随机、单盲、阳性药(双氯芬酸乳胶)平行对照。
4) latexes
乳胶
1.
The results show that the rate of polymerization increases with increasing emulsifier concentration, initiator concentration and temperature, the nucleation period finishes earlier and the particle average diameter of latexes is larger than the particle produced by traditional emulsion polymerization.
对反应性乳化剂作用下的醋酸乙烯酯(VAc)乳液聚合动力学体系进行了研究,实验结果发现,聚合速率随乳化剂、引发剂浓度、温度的增大而加快,乳胶粒平均直径较传统的的乳液聚合乳胶粒子大得多,且成核期结束较早。
5) latex adhesive
乳胶
1.
The polyacrylate latex adhesives have been synthesized to meet the requirements of the development of the coated abrasives products.
根据砂布磨具对胶粘剂的性能要求 ,合成了聚丙烯酸酯乳液胶粘剂 ;考察了共聚体系中各种原料的组合、配比及用量对乳胶机械性能的影响。
6) latex
[英]['leɪteks] [美]['letɛks]
乳胶
1.
Analysis of the Water-soluble Proteins in Medical Latex Gloves
医用乳胶手套中水溶性蛋白质的含量分析
2.
The influence of the composition, ratio of network Ⅰ to network Ⅱ, the kinds and amounts of crosslinker on miscibility and damping properties of multicomponent latex interpenetrating polymer networks (LIPNs) were investigated with a rheovibron viscoelastometer.
用动态粘弹谱仪研究多组分乳胶ＩＰＮ’ｓ 体系网络的组成、配比、交联剂品种及用量等因素对体系相容性及阻尼性能的影响。
3.
The super microstructure of the outer coating of some natural latex catheters made in China and abroad with TEM was described.
用透射电镜（ＴＥＭ）观察研究了国内外几种天然乳胶导尿管外涂层的超微结构，并与其性能作了比较，结果表明，涂层的厚度和均匀度及对胶层的渗透程度直接影响产品的使用性能。
补充资料：离心胶乳
分子式：
分子量：
CAS号：
性质：用离心法浓缩的天然橡胶胶乳。将胶乳加入特种高速离心机中，借离心力的作用使大部分胶乳粒子与乳清分开，而得浓度达67％的浓缩胶乳。乳清中含有大部分非橡胶成分和少量微小胶乳粒子。如果反复用离心法浓缩，可得到纯度较高的浓缩胶乳。一般纯度愈高，稳定性则愈低。离心胶乳干燥较快，硫化较慢，硫化胶的永久变形较低。
分子量：
CAS号：
性质：用离心法浓缩的天然橡胶胶乳。将胶乳加入特种高速离心机中，借离心力的作用使大部分胶乳粒子与乳清分开，而得浓度达67％的浓缩胶乳。乳清中含有大部分非橡胶成分和少量微小胶乳粒子。如果反复用离心法浓缩，可得到纯度较高的浓缩胶乳。一般纯度愈高，稳定性则愈低。离心胶乳干燥较快，硫化较慢，硫化胶的永久变形较低。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条