1) jelly melting point
凝胶熔化温度
2) gelation temperature
胶凝温度
1.
The aim of the present work is to investigate the characteristics including gelation temperature, sol-gel transition temperature (T_ s-g ), gel strength, stable viscosity, erosion and drug release behavior of the thermosensitive in situ gel which are composed o.
本文以泊罗沙姆Pluronic F127为温度敏感原位凝胶材料,考察了PluronicF127与Pluronic F68不同浓度处方对地塞米松磷酸钠温度敏感原位凝胶的胶凝温度、相转变温度、凝胶强度、稳态黏度、溶蚀和药物释放行为等特性的影响。
2.
The experimental results show that the gelation temperature at which G'= G", coincides with the gel point when the temperatu.
5-1℃/min,储能模量(G’)和耗能模量(C”)相等时的胶凝温度与按SY/T0541-94方法测定凝点基本一致,说明用小振幅振荡剪切温度扫描法来确定含蜡原油的凝点是可行的。
3.
The gelation extent and structure strength can be revealed by the viscoelastic parameters and gelation temperature measured by small amplitude oscillatory shear experiment.
结果表明,储能模量和耗能模量随测量温度的降低呈指数规律增加;存在使流变性恶化的“最差加热温度”;降温速率越高,测量温度下蜡晶结构强度和胶凝温度越低。
3) Gelation temperature
凝胶温度
4) melting temperature
熔化温度
1.
Study on size effect of melting temperature of Pb nanowires;
铅纳米线熔化温度的尺寸效应研究
2.
Molecular dynamic study on size dependent melting temperature of Pb nanofilms;
铅纳米薄膜熔化温度尺寸效应的分子动力学研究
3.
Influence of interaction among agglomerative flux components on melting temperature of flux;
焊剂组元间交互作用对熔化温度的影响
5) melting point
熔化温度
1.
Free energy method and the melting point of aluminum under the zero pressure;
自由能方法与零压下Al的熔化温度
2.
The effects of Li2O,NaF,Al2O3 and ZnO on soften and melting point of glass frits was studied.
研究了Li2O,NaF,Al2O3和ZnO对玻璃体系软化温度和熔化温度的影响,在此基础上研制出了软化温度Tg低于500℃、熔化温度Tm低于560℃的低温无铅玻璃。
3.
The influences of copper on properties of Zn-Al solders for Al/Cu brazing,which include wettability,shear strength of joint,microstructure of weld and melting point were studied.
研究了Cu元素对铝/铜钎焊用Zn-Al钎料的熔化温度、铺展性、接头剪切强度及焊缝组织的影响。
6) gel temperature
热凝胶温度
1.
It s also discussed the reason of the decrease of viscosity and gel temperature that occurs in cement products with the manufacturing experience.
纤维素醚是一种可用于水泥制品中的多用途添加剂 ,本文介绍了水泥制品中常用品种甲基纤维素 (MC)和羟丙基甲基纤维素 (HPMC)的化学性质、溶解方法和原理及其溶液的主要特性 ,并结合实际生产经验对水泥制品中容易造成的热凝胶温度和粘度的下降现象进行了探讨。
补充资料：Sds-聚丙烯酰胺凝胶电泳凝胶电泳
sds-聚丙烯酰胺凝胶电泳（sds-page，sodium dodecyl sulfate-polyacrylamide gel electrohoresis）
在有去污剂十二烷基硫酸钠存在下的聚丙烯酰胺凝胶电泳。sds-page只是按照分子大小分离的，而不是根据分子所带的电荷和大小分离的。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条