1) YJ19A cigarette maker
YJ19A卷烟机
1.
The shortcomings influencing weight stability of cigarette in original weight control system in YJ19A cigarette maker were indicated: the ecreteur discs were relatively far away from the trough rails when tobacco was trimmed.
分析了YJ19A卷烟机原重量控制系统存在的影响烟支重量稳定性的设计缺陷:劈刀修剪烟丝时,劈刀与烟丝导轨距离较大,并对其进行了改进。
2) YJ19 cigarette maker
YJ19卷烟机
1.
Aiming at the problem of screen block in the feeding airlock in YJ19 cigarette maker, the airlock was improved: putting an inclined screen to replace levelled one inside the airlock and adding an internal suction pipe to automatically clean the screen with the suction air supplied by the pneumatic conveying system.
针对YJ19卷烟机落料器滤网堵塞的问题,对落料器结构进行了改进。
2.
The mechanical structure of and position relationship between cut-off knife and ledger in the improved YJ19 cigarette maker were analyzed,and the makeup and realization of the electrical system were discussed.
分析了改造后YJ19卷烟机刀头、喇叭嘴的机械结构及位置关系,提出采用博世交流伺服电机解决两者的同步问题,并对电气系统的构成及实现进行了详细论述。
3.
The rod breaker in YJ19 cigarette maker had complex mechanism and long gearing chain, and its stability and reliability were not satisfactory.
YJ19卷烟机打条器结构复杂,传动路线长,稳定性和可靠性差。
4) PROTOS 70 cigarette maker
PROTOS70卷烟机
5) cigarette machine
卷烟机
1.
This paper introduces the application of industry control computer in cigarette machine group monitoring and management system.
介绍微机在卷烟机组监控及管理系统中的应用，主要介绍监控及管理的软件设计思想及技术难点。
2.
The basic principle of paper supply is introduced for packaging machines It is investigated to apply inverter drive to paper supply with equal tension The cigarette paper supply with equal tension is presented The paper tension detected for the highly speed cigarette machine is described and the system diagram is give
本文介绍卷烟机中供纸的基本原理 ,讨论变频技术在等张力供纸控制系统中的应用方法 ,并以高速卷烟机为研究对象 ,详细介绍高速卷烟机等张力供纸系统的构成 ,供纸张力的检测方法以及采用变频技术控制的基本思想 ,给出了相应的控制原理
3.
The PID weight control system s structure of MK95 cigarette machine was introduced and the principle about the control system was analyzed, such as the check of weight symbol, PID parameter choice.
介绍了MK95卷烟机PID重量控制系统的结构,对其控制原理进行了分析重量信号的检测、控制过程、削减盘电机速度控制、数字PID控制算法的实现、PID参数选择。
补充资料：C-803（yj-83）
c-803延续了c-802的弹体气动布局，长度 似乎较c-802的6。4米更甚，其上保留了c-802的小型涡喷发动机结构，弹头整流罩较前者略为尖细，采 新型固体火箭发动机，此外，折叠式弹翼的前面有一接收资料链的天线，可接受舰艇、直升机、甚至卫 星的导引，也是分辨c-803同之前型号的主要识别标记。c-803的发射箱也同以往有异，上有三条加强肋 筋，显示弹箱可承受导弹发射时更高的冲压，箱盖舍弃了鹰击81/82的破片式改采上下开启式，轧制成形 的凹凸面也稍有不同。 同意大利的“奥图马斯”改良型和俄罗斯最新研制的3t-54y1舰舰导弹类似，c-803也采用了高亚音速巡 航，超音速终程俯冲攻击的作战模式。助推器先将导弹加速到高亚音速后由涡喷发动机接管，此时助推 器脱离弹体。当外部资料链或导弹自身弹上计算机启动终程攻击程序后，二级火箭发动机点火，涡喷发 动机脱离，导弹进入俯冲飞行状态，此时的导弹将在离目标20-30公里处达到1。3~1。5马赫的低超音 速，取决于是否需要作战术机动动作。 c-803还有空射型和潜射型，不久也将陆续装备海航的歼轰-7、苏-27和“宋”级常规潜艇。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条