1) stress orientation
应力方向
1.
The paper approaches the relationship among fault capable degree,toctonic stress orientationand geometric characteristics of fault plane in three dimensions by the method of Mohr stress circle.
文章应用应力摩尔圆分析法，探讨了三维空间状态下断层能动度与构造应力方向和断层面几何特征的关系。
2.
Temporal-spatial characteristics of stress orientation in the area are studied in this paper.
1994— 2 0 0 0年间川滇地区小震震源机制解的分析结果显示 ,川滇地区的应力场存在以丽江—小金河断裂为界的分区特征 :丽江—小金河断裂以北地区 (北区 )存在双重力源应力场 ,而南部地区(南区 )应力方向单一 ;并发现北区在 1996年前后发生过一次应力场转向事件 ,转变前后的应力主轴方位分别对应双重力源的两个方向 ,反映了双重力源在北区随时间的相互作用。
3.
The stress orientation and relative stress parameter before and after Tangshan earthguake have been analyzed by meanse of azimuthal feature releasing seismic energy in this paper.
用地震能量释放的方位特征分析了唐山地震前后的应力方向及有关应力参数的特点及其变化。
3) principal stress direction
主应力方向
1.
Research on strength and pore pressure of intact clay considering variation of principal stress direction;
考虑主应力方向变化的原状黏土强度及超静孔压特性研究
4) shear stress direction
剪应力方向
5) orientation of principal stress
主应力方向
1.
The coefficient of intermediate principal stress and orientation of principal stress are varied so that their influences on shear b.
试验过程中,控制平均主应力保持不变,分别探讨在排水与不排水条件下中主应力系数和主应力方向角对饱和砂土剪切特性和强度的影响。
2.
The coefficient of intermediate principal stress and orientation of principal stress are varied so that their coupled influences on shear behaviors of saturated sand are explored.
针对相对密度为30%的福建标准砂,利用土工静力-动力液压-三轴扭转多功能剪切仪,在不同初始固结条件下控制试验过程的平均主应力保持不变,改变中主应力系数和主应力方向,进行了应力控制式单调排水剪切试验,着重探讨中主应力系数和主应力方向对砂土剪切强度的耦合影响。
3.
Based on the comparative experimental results,the effects of orientation of principal stresses and relative density on shear strength as well as volumetric characteristics were respectively investigated.
应用大连理工大学研发的土工静力-动力液压-三轴扭转多功能剪切仪,控制试验过程的平均主应力和中主应力系数保持恒定,改变主应力方向,针对相对密度为30%、60%的饱和福建标准砂,进行一系列排水单调剪切试验。
6) orientation of stress field
应力场方向
补充资料：轧辊残余应力(见轧辊应力)
轧辊残余应力(见轧辊应力)
residual stresses in roll
zhagun eanyu yingli轧辊残余应力(residual stresses in roll)见礼辐应力。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条