1) upper metabainite
准上贝氏体
1.
An investigation of the interfacial misfit dislocation at bainitic ferrite(BF)retained austenite(Ar) interface of upper metabainite has been undertaken in a BZ30 Sicontaining steel by means of weakbeam darkfield TEM.
运用透射电镜研究了含Ｓｉ钢准上贝氏体中贝氏体铁素体（ＢＦ）／残余奥氏体（ＡＲ）的界面错配位错，发现是混合型位错，使得界面能沿其法线方向作滑移运动，表明贝氏体可以切变形成。
2) meta-bainite
准贝氏体
1.
In present paper the effects of overload on the fatigue crack initiation life ofmeta-bainite and martensite in steel 40CrMnSiMoV have been investigated.
本文研究了超载对40CrMnsiMoVA 钢中准贝氏体组织和马氏体组织冲击疲劳裂纹起始寿命的影响。
3) Upper bainite
上贝氏体
1.
The results show that the appearance of Widmanstatten structure,upper bainite and martensite in the structure of 20MnSi HRB is the main cause making the yield point disappear.
结果表明 :2 0 Mn Si热轧带肋钢筋中出现的魏氏组织、上贝氏体及马氏体组织是使屈服点消失的主要原因。
2.
The main reason why mechauical propcrties of qutnched and tem-Pered hcavy part or 35CrMo steel,such as impact toughness and so on,are impossiblc to meetthe requirements is regarded as tbe presentation or the upper bainite in its microstructure.
本文总结了多年来有关35CrMo钢热处理的经验，认为35CrMo钢制大件调质处理后冲击韧性等力学性能达不到要求的原因主要是组织中出现较大量的上贝氏体。
3.
The results show that upper bainite and grain boundary segregation of Si element result in embrittlement of the oil cylinder.
结果表明,上贝氏体和Si元素的晶界偏聚导致油缸变脆。
4) meta-bainitic steel
准贝氏体钢
1.
Wear resistance and wear mechanism of carburized layer of meta-bainitic steel in pin-on-disk abrasive wear and impact abrasive wear were investigated.
研究了准贝氏体钢销盘磨料磨损和冲击磨料磨损的耐磨性和磨损机制 ,确定了回火温度对耐磨性的影响 ,探讨了残余奥氏体的机械稳定性及其对耐磨性的作用。
2.
As a constructional material in the 21st century, the Ultra-grade steels STX21 of Japan and the new type meta-bainitic steel series of our country have been introduced.
介绍了作为21世纪结构材料日本超级钢铁材料STX21和我国新型系列准贝氏体钢。
3.
A series of new type meta-bainitic steel is presented in this paper.
介绍了我们多年的研究成果─—新型系列准贝氏体钢，该系列钢具有独特的组织和性能，以及广阔的应用前景。
5) meta bainitic steel
准贝氏体钢
1.
Carburized characteristics and carburization technology of Si Mn Mo meta bainitic steel were investigated in comparision with 18Cr2Ni4WA.
对比研究了 Si- Mn- Mo系准贝氏体钢和 18Cr2 Ni4WA钢的渗碳特性和渗碳工艺 ,结果表明 :准贝氏体钢具有较好的渗碳特性 ,尤其是优越的空冷淬硬性 ,并确定了准贝氏体钢的渗碳工
2.
Carburization characteristics and wear behavior of new type meta bainitic steel were studied.
研究了新型准贝氏体钢渗碳特性及渗层磨损性能。
3.
A new series of meta bainitic steels is founded by adding in appropriate amount of silicon on the alloying basis of bainitic steel.
准贝氏体钢是在贝氏体钢合金化的基础上添加适量的硅而组成的。
6) meta-bainite steel
准贝氏体钢
1.
Research progress of service properties of meta-bainite steel;
准贝氏体钢使用性能研究进展
补充资料：奥氏体-贝氏体球铁
分子式：
CAS号：
性质：又叫奥-贝球铁。基体组织为奥氏体加贝氏体组织的球墨铸铁。这类球铁硅含量一般在1.4%～3.8%。含锰量小于0.5%，与普通球铁比较硅偏高、锰偏低。通过调节化学成分与热处理获得理想的奥-贝球铁的基体组织为针状贝氏体或无碳贝氏体一富碳奥氏体。这类球铁具有优良的综合机械性能、强度高、耐磨性好、韧性好、特别是有高的缺口韧性，可代替钢，用于制作重要受力结构件，如曲轴、齿轮、凸轮轴等。
CAS号：
性质：又叫奥-贝球铁。基体组织为奥氏体加贝氏体组织的球墨铸铁。这类球铁硅含量一般在1.4%～3.8%。含锰量小于0.5%，与普通球铁比较硅偏高、锰偏低。通过调节化学成分与热处理获得理想的奥-贝球铁的基体组织为针状贝氏体或无碳贝氏体一富碳奥氏体。这类球铁具有优良的综合机械性能、强度高、耐磨性好、韧性好、特别是有高的缺口韧性，可代替钢，用于制作重要受力结构件，如曲轴、齿轮、凸轮轴等。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条