1) resemblance principle

浇嘴系统
2) pouring system

浇注系统
1.
Study of the calculating formulas in the minimum section of the gray casting iron pouring system
灰铸铁件浇注系统最小截面积计算公式研究
2.
The injection molding flow of six different pouring system for air-condition panel was analyzed respectively by using Molding Plastics Advisers (MPA)software.
利用模流分析软件Moldflow Plastics Advisers(MPA)对空调机面板注塑模6种构型不同的浇注系统分别进行注射成型流动分析。
3.
The structural characteristics of the aluminum alloy tap part were analyzed, and the design of pouring system and die-casting die structure were introduced.
分析了铝合金水龙头零件的结构工艺性特点,介绍了压铸模的浇注系统及模具结构设计。
3) gating system

浇注系统
1.
Simulation and optimization of gating system of die-casting die for magnesium alloy AM60B part;
AM60B镁合金压铸模浇注系统的模拟与优化
2.
Principle of Designing Gating System for Die Cast Aluminum Alloy Mould;

设计铝合金压铸模具浇注系统类型的原则
3.
Optimization of Gating System for Gear Box of the Car Based on CAE System;

基于CAE分析的汽车齿轮室浇注系统的优化
4) runner system

浇注系统
1.
Design of runner system of injection mould for cellphone glass block;

手机镜片注射模浇注系统设计
2.
Manmade balanced design and numerical simulation for unbalanced runner system;

非平衡浇注系统的人工平衡设计与数值仿真
3.
Optimization of front bumper runner system and its implementation

汽车前保险杠浇注系统优化及实施
5) feed system

浇注系统
1.
Research and development on knowledge-based feed system for injection mould;

基于知识的注塑模浇注系统的研究与开发
2.
Research on the Intelligent Design Technology of Injection Mould Feed System Based on Knowledge;
基于知识的注塑模具浇注系统智能化设计技术研究
3.
Optimization of feed system and design of injection mould for automotive engine cover

汽车发动机罩盖浇注系统优化与注射模设计
6) injection system

浇注系统
1.
The design of injection system for big-size bending thinning plastic;

大规格弯曲薄壁塑件注射成型浇注系统设计
2.
Factors influencing the injection system were investigated as well as the control and adjustment on its balance.
分析了多模腔注塑模具分流道的平衡性,探讨了浇注系统的影响因素以及浇注系统平衡的控制与调节,结果表明:同模多腔模具流道非平衡排布时,可通过调节浇口的长度及截面尺寸来补充流道长度的差异而引起的不平衡;而对于异模多腔模具,应将模腔容积作为调整系数,依此来设计流道的长度和浇口的长度及截面尺寸。
3.
The structure characteristics and technology requirement of the washer sliding were analyzed, designed the injection mold with an ordinary injection system and three layers, solved the problem of automatic demould, the die structure and working process were introduced, practical production showed the die is safe and reliable, and it improved manufacturing efficiency.
分析了塑件的形状特点和技术要求,设计了一副普通浇注系统3层注射模,并解决了该注射模的自动脱模问题。
补充资料:一体化热浇口系统省时增效
![]() | |||
|
说明:补充资料仅用于学习参考,请勿用于其它任何用途。
参考词条