1)  indefectible point
					 
	
					
				
				 
	
					
				无亏损点
			
					2)  no-loss level
					 
	
					
				
				 
	
					
				无亏损水平
			
					3)  momentumless wake
					 
	
					
				
				 
	
					
				无动量亏损尾迹
				1.
					Experimental investigation on the momentumless wake;
					 
					
						
						 
					
						无动量亏损尾迹的实验研究
					2.
					Experimental investigation on the interaction between momentumless wake and rotor based on PIV
						
						基于PIV实验研究无动量亏损尾迹与动叶相互干涉的流场
					3.
					Through experiment,trailing edge blowing up to momentumless wake can reduce the noise.
					 
					
						
						 
					
						本文对尾缘喷气用于低压轴流风机进行了详细的研究,对轴流风机的上游静叶实施尾缘喷气,通过实验测量,尾缘喷气使静叶尾迹达到无动量亏损尾迹状态能够降低风机噪声,文章还提出了基于CFD数值模拟的尾迹与动叶相互干涉的噪声预测模型,预测结果和实验结果比较接近。
					
					4)  loss
					[英][lɔs]  [美][lɔs]
					 
	
					
				
				 
	
					
				亏损
				1.
					The loss status of the WR project  management units and the turning loss measures;
					 
					
						
						 
					
						广西水利工程管理单位亏损情况及扭亏措施
					2.
					Cultural Implication Loss &Compensation in Rendering Names of Poetic Place in Tang Poems;
					 
					
						
						 
					
						唐诗英译中诗化地名意蕴传递的亏损和补偿
					
					5)  deficit
					[英]['defɪsɪt]  [美]['dɛfəsɪt]
					 
	
					
				
				 
	
					
				亏损
				1.
					Thoughts on Amtrak s deficit;
					 
					
						
						 
					
						美国Amtrak亏损问题初探
					2.
					Reasons on deficit and countermeasures for resources-exhausted coal enterprises;
					 
					
						
						 
					
						资源枯竭型煤炭企业亏损原因及对策
					3.
					The analysis of cause of deficit of university-run enterprise;
					 
					
						
						 
					
						高校校办产业亏损原因浅析
					
					6)  losses
					[英][lɔs]  [美][lɔs]
					 
	
					
				
				 
	
					
				亏损
				1.
					In the economic transitional period,state-owned enterprises in China experience painful losses which are often related to the increase of production volumes and the sharpening of market competition.
						
						在经济转轨过程中国有企业经历了惨痛的亏损阶段,国有企业的亏损与国有企业的产量扩大以及市场竞争结构等方面因素有关。
					补充资料:闭式单点、双点压力机
		| 
 | |||||||
| 主要参数内容 | 国际先进 | 国内先进 | 国内一般 | 国内落后 | 评定方法及说明 | ||
| (一)加工精度 | 参照GB10924-89、GB10933-89、JB5200-91 | ||||||
| 1、滑块下平面对工作台上平面的平行度(mm) | 30%精度储备 | 20%精度储备 | 达到规定值 | 大于规定值 | |||
| 0.02+0.10/100×滑块下平面的被测长度 | |||||||
| 2、滑块行程对工作台上平面的垂直度 | 30%精度储备 | 20%精度储备 | 达到规定值 | 大于规定值 | |||
| 0.05+0.02/100×滑块行程长度 | |||||||
| (二)结构性能 | |||||||
| 1、离合器、制动器接通率,当滑块行程次数≤16次/分时为70%,≤25次/分时为60%,≤45次/分时为50% | 大于规定值10% | 大于规定值 | 达到规定值 | 达不到规定值 | |||
| 2、液压超负荷保险装置、微调装置、吨位指示器 | 全部具有 | 全部具有 | 部分具有 | 没有 | |||
| (三)噪声dB(A) | |||||||
| 1、公称力≤400kN | ≤85 | ≤87 | ≤88 | >88 | |||
| 2、公称力>400kN | ≤87 | ≤88 | ≤90 | >90 | |||
说明:补充资料仅用于学习参考,请勿用于其它任何用途。
	参考词条