1) carbonic reheating agent
碳质发热剂
1.
And some problems such as the oxidizing rate and the fully burning of carbon,the composition and shaping of carbonic reheating agent have been analyzed.
讨论分析了碳的氧化速度和完全燃烧，以及碳质发热剂的组成与成型等问题。
2) carbothermal evaporation
碳热蒸发
1.
Several different morphologies of SnO2 nanostructures were prepared on single crystal silicon substrate by Au-Ag alloying catalyst assisted carbothermal evaporation.
通过金银合金助催的碳热蒸发方式,在单晶Si衬底上生长了几种不同形貌的SnO2纳米结构。
3) carbon-carbon bond type initiator
碳-碳键引发剂
4) carbonaceous reducer
碳质还原剂
1.
The microwave-absorbing characteristics of the mixtures about carbonaceous reducer and ilmenite were measured by the technique of microwave cavity perturbation and the relationships between p and the microwave-absorbing characteristic of the mixtures were studied.
采用微波谐振腔微扰法测定了碳质还原剂和钛精矿混合物料的吸波特性,研究了碳质还原剂配入钛精矿不同比例时混合物的吸波特性与材料的复介电常数(ε″)、微波场内热源强度p的关系。
2.
The microwave-absorbing characteristics of the mixtures of carbonaceous reducer and zinc-kiln slag were measured by the technique of microwave cavity perturbation and the relationships between P(P=ωε″E2V) and the microwave-absorbing characteristic of the mixtures were studied.
采用微波谐振腔微扰法测定碳质还原剂和锌窑渣混合物料的吸波特性,研究碳质还原剂配入锌窑渣不同比例时混合物的吸波特性与材料的复介电常数(ε″)、微波场内热源强度P(P=ωε″E2V)的关系。
5) carbonaceous binder
碳质结合剂
1.
Newly-developed carbonaceous binder for carbon-containing refractories:a comparative analysis;
含碳耐火材料用新型碳质结合剂的对比分析
6) carbon reductant
碳质还原剂
1.
Operation process of ferrosilicon manufacturing with carbon reductant of total petroleum coke is intro-duced and well technico-economical index are obtained.
介绍了在硅铁生产中全部用石油焦作碳质还原剂的应用,指出用此法生产可取得良好的经济技术指标。
补充资料：铝碳质整体塞棒
铝碳质整体塞棒
alumina graphite monolithic stopper
IUtanzhi zhengti sa}bdng铝碳质整体塞棒(alumina graphite monoli-thicst叩per)以刚玉和鳞片状石姜为主要原料烧成的控制钢液流量的耐火制品。其特点是整体性好，代替了由传统的袖砖和塞头组装的塞棒，使用更安全，而且还可以通过塞棒向中间罐水口吹氢，净化钢水，防止水口堵塞。 铝碳质整体塞棒的理化指标:A120360%，F·C25%，体积密度2.359/c m3，显气孔率13%，耐压强度14.7MPa，抗折强度(1400℃)5.oMPa，线膨胀率(1000℃)。.5%。其制造工艺是将刚玉、石墨和添加剂等原料按配比称量，以酚醛树脂为结合剂，经混练，用等静压机成型。半成品经干燥后，在无氧化烧成窑内烧成。最后，经X射线无损探伤、车床加工、喷涂防氧化涂层等工序，经检验合格后为成品。铝碳质整体塞棒的工艺流程见图。 刚玉石墨添加剂福猛啮~遍州画画趣画莎甲’ 成品 铝碳质整体塞棒的生产工艺流程 在制造中，配料要准确，原料要符合工艺要求，泥料必须造粒，成型压力为120~150MPa，烧成温度为1000~1350℃。 该制品安装于连铸机中间罐内，用其开启程度来控制钢水流量的大小.要求干燥贮存，使用前必须预热。 (周川生)
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条