1) polyether quenching medium
聚醚淬火介质
1.
Selection of composition of polyether quenching medium have been carried out by the hardness method.
利用硬度评定法对聚醚淬火介质的成分进行了优选，结果表明：４５钢试样在浓度为１５％的聚醚水溶液淬火介质中淬火，不但表面硬度高，而且硬度梯度平缓。
2) polymer quenchants
聚合物淬火介质
1.
Deals with some common characteristics of polymer quenchants and assesses the cooling behavior of the newly developed WGY medium which is used in production.
介绍了聚合物淬火介质的一些共性特点，对新研制成功并已用于生产的ＷＧＹ型淬火剂的特点及冷却特性进行了描述，并与国内外同类产品进行了比较。
3) quenchants
淬火介质
1.
The most common quenchants are water aqueous,polymer solutions and mineral oil.
最常见的淬火介质有水溶液、聚合物溶液和矿物油。
4) quenchant
淬火介质
1.
Application of polymer quenchant;
聚合物水基淬火介质的应用
2.
Calculation on Heat Transfer Coefficient of Several Typical Steels in Different Quenchants;
多种常用钢在不同淬火介质中换热系数的测算
3.
Studies on Preparation and Properties of Polyalkylene Glycol Quenchant;
聚烷撑二醇（PAG）淬火介质的研制及性能研究
5) quenching media
淬火介质
1.
The test methods of cooling characteristics of quenching media were introduced,some problems during implementation of two standards such as JB/T 7951—2004 《Industial quenching oil-determination of cooling characteristics –nickel-alloy probe test method》 and SH/T 0220—1992 《Heat treating oils-determination of cooling ability》,the test error analysis and benchmarking method were discussed.
介绍了淬火介质冷却性能的测试方法,并分析讨论了JB/T7951—2004《测定工业淬火油冷却性能的镍合金探头实验方法》和SH/T0220—1992《热处理油冷却性能测定法》两个淬火介质冷却性能测试标准在执行过程中存在的一些问题、测试误差的分析及标定的方法。
2.
A software system is developed to test the cooling performance of quenching media.
基于作者所开发的淬火介质冷却性能测试软件系统 ,概述了系统的构成、软件的设计及实现 ,具体分析了数据处理系统部分数学模型及数学处理方法 ,为编程提供了理论基础。
3.
The variation temperatures of the probe surface are used to determine the cooling characteristics of quenching media.
以探头表面的温度变化情况来分析淬火介质的冷却能力。
6) quenching medium
淬火介质
1.
Polymer quenching medium and its development;
水溶性聚合物淬火介质及其发展
2.
Study of Mangetoelectric Measurement on Cooling Characteristics of Quenching Mediums;
淬火介质冷却特性磁电测试的研究
3.
Effect of quenching medium and small addition of Ag on microstructure and properties of Al-Zn-Mg-Cu alloy
淬火介质及微量Ag对Al-Zn-Mg-Cu合金组织性能的影响
补充资料：聚氯醚,氯化聚醚
CAS：25323-58-4
分子式：(C5H8Cl2O)x
中文名称：聚3,3-双(氯甲基)丁氧环；氯化聚醚；聚氯醚,氯化聚醚
英文名称：Poly 3,3-bis(chloromethyl)oxetane；Chlorinated polyether；3,3-bis(chloromethyl)-oxetan homopolymer
分子式：(C5H8Cl2O)x
中文名称：聚3,3-双(氯甲基)丁氧环；氯化聚醚；聚氯醚,氯化聚醚
英文名称：Poly 3,3-bis(chloromethyl)oxetane；Chlorinated polyether；3,3-bis(chloromethyl)-oxetan homopolymer
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条