1) mode function combination method

模态组合法
2) modes composition

模态组合
3) state compounding method

状态组合法
1.
The state compounding method and control strategy applied in voltage mode PWM inverter is presented.
文中根据电压型PWM逆变器的特点提出了状态组合法,并运用状态组合法得到电压型PWM逆变器输出电压波形的控制策略。
4) Dynamic combination method

动态组合法
5) mode synthesis method

模态综合法
1.
Critical speeds of modern high-speed hollow spindle are calculated, and the influences of main structural parameters upon critical speed are also studied using component mode synthesis method.
采用子结构模态综合法计算了新型高速空心锭子的前二阶临界转速,讨论了空心锭子主要结构参数临界转速的影响,提出了适应不同工作转速的空心锭子结构参数选择范围。
2.
The bridge and the vehicle are treated as two branches of a coupling dynamic system respectively, and the mode synthesis method is applied to analyzing the responses of the coupling system.
车辆和桥梁可看成一个整体耦合动力学系统的两个分支 ,并引入模态综合法来分析其动力响应。
3.
The main problem of the mode synthesis method, applied in structural vibration analysis of prefabricated bridges, is how to select relevant number of low frequency modes synthesized during the course that displacements of substructures are expressed in generalized coordinates that are defined by displacement modes.
模态综合法应用于装配式桥梁结构振动分析的主要问题 ,是在将子结构坐标缩聚为模态广义坐标的过程中 ,如何选取适当数目的低阶模态来参与综合。
6) component mode synthesis

模态综合法
1.
Application of component mode synthesis in ANSYS;

模态综合法在ANSYS中的应用
2.
Then,the basic principle of free interface component mode synthesis was introduced.

介绍了具有线性和非线性连接子结构的自由界面模态综合法的基本原理,并采用该方法建立了考虑副车架橡胶支承迟滞特性的整车非线性动力学模型,用所建模型对汽车动力特性进行了数值仿真,并通过试验对仿真结果进行验证。
3.
For a car including power train,engine cradle,car body,mass without spring and those substructures with linear and nonlinear joints,the scheme of component mode synthesis is employed to model dynamical systems of the car with hysteresis nonlinearity and rigid-elastic coupling.
将整车模型划分为多个子结构,包括动力总成子结构、副车架子结构、车身子结构、非簧载质量子结构及多个线性和非线性连接子结构等,采用含线性和非线性连接子结构的间接对接的自由界面模态综合法,建立整车迟滞非线性刚弹耦合系统动力学模型。
补充资料:组合凹模与凸模
当制件形状复杂、尺寸较大或很小、精度要求高时,一般采用组合式结构
图8-5 P174
a)为组合凸模的例子 b)为组合凹模的例子
设计时:螺孔的位置应靠近刃口,销孔的位置应远离刃口
凹模的例子(书上没有讲清楚),看补充讲义P1
补充:
1) 平面式(图35) 为什么分3块?使用和加工方便,可分块加工,分块拆换
用螺钉及销定固定到固定板或底座上
一般用于大型模具或多孔模具
2) 凸边式(图36) 把凹模的各拼块嵌入两边或四边的凸边固定块内,凸边的高度不小于拼块高度H的一半,凸边的宽度大于两倍销钉直径d
适用于冲制薄料和小制件
将内加工改为外加工,下面两种分块法更好?
3) 套筒式(图37) 把凹模或凸模按不同直径分割成几个同心圆套筒,分别加工后相互套合组成。
4) 种植式(图37)将凹模中难于加工或悬臂很长受力危险的部分分割出来,做成凸模形式的镶块,嵌入凹模里固定牢,并在凹模下面增加淬硬垫板。
说明:补充资料仅用于学习参考,请勿用于其它任何用途。
参考词条