说明:双击或选中下面任意单词,将显示该词的音标、读音、翻译等;选中中文或多个词,将显示翻译。
您的位置:首页 -> 词典 -> 低速滚动轴承
1)  low-speed rolling bearing
低速滚动轴承
1.
Study on fault diagnosis of low-speed rolling bearing using stress waves and wavelet analysis;
基于应力波与小波分析的低速滚动轴承故障诊断研究
2.
Following the fault characteristics of low-speed rolling bearings,we propose a new method for diagnosing their faults.
低速滚动轴承结构和工作条件特殊,故障机理复杂,诊断难度较大。
2)  Low noise rolling bearings
低噪声滚动轴承
3)  medium to high speed ball bearing
中高速滚动轴承
1.
Therefore lubrication of the medium to high speed ball bearing using in space effective payload under the high vacuum condition is one of the main challenges.
运动部件的长寿命可靠性是空间有效载荷可靠性的关键,在空间高真空环境中使用的中高速滚动轴承的润滑是其中的难点之一。
4)  High-speed roller bearing
高速滚动轴承
1.
Development and Application for High-speed roller bearing Expert System;
高速滚动轴承专家系统的开发与应用
5)  ball bearing
滚动轴承
1.
Nonlinear dynamic response analysis of unbalance-rubbing coupling faults of rotor-ball bearing-stator coupling system;
转子-滚动轴承-机匣耦合系统的不平衡-碰摩耦合故障非线性动力学响应分析
2.
Model for dynamic characteristics produced by inner race local defect in ball bearing system and its simulation;
内圈局部损伤滚动轴承系统动态特性建模及仿真
3.
Extraction of the Fault Features of Ball Bearings Based on Bispectrum Analysis;
基于双谱分析的滚动轴承故障特征提取
6)  roller bearing
滚动轴承
1.
Analysis of load characteristic of roller bearing on work roll for an Aluminum foil mill;
铝箔轧机工作辊滚动轴承负荷特性分析
2.
Analyse on the Damage of Mill Roller Bearing and Its Prevention;
压榨机滚动轴承失效原因分析及其改进措施
3.
Morphology filters for analyzing roller bearing fault using acoustic emission signal processing;
形态滤波在滚动轴承故障声发射信号处理中的应用
补充资料:滚动轴承
滚动轴承
ball and roller bearing

   在滚动摩擦下工作的轴承。滚动轴承使用维护方便,工作可靠,起动性能好,在中等速度下承载能力较高。与滑动轴承比较,滚动轴承的径向尺寸较大,减振能力较差,高速时寿命低,声响较大。滚动轴承中的向心轴承(主要承受径向力)通常由内圈、外圈、滚动体和滚动体保持架4部分组成。内圈紧套在轴颈上并与轴一起旋转,外圈装在轴承座孔中。在内圈的外周和外圈的内周上均制有滚道。当内外圈相对转动时,滚动体即在内外圈的滚道上滚动,它们由保持架隔开,避免相互摩擦。推力轴承分紧圈和活圈两部分。紧圈与轴套紧,活圈支承在轴承座上。套圈和滚动体通常采用强度高、耐磨性好的滚动轴承钢制造,淬火后表面硬度应达到HRC60~65。保持架多用软钢冲压制成,也可以采用铜合金夹布胶木或塑料等制造。
   
   

不同型号的滚动轴承

不同型号的滚动轴承


   
   滚动轴承种类很多。①按承载方向可分为向心轴承(承受径向力及不大的轴向力)、推力轴承(只能承受轴向力)和向心推力轴承(能同时承受径向力和轴向力)。②按滚动体形状可分为球轴承、滚子轴承和滚针轴承。③按工作条件可分为普通轴承、高速轴承、高温轴承、低温轴承、真空轴承、防磁轴承、耐腐蚀轴承、精密微型轴承和特大型轴承等。中国把各种类型的滚动轴承分成B、C、D、E、G 5个精度等级,B为最高精度级,G为普通精度级,应用最普遍。
   滚动轴承是标准件,由专门的轴承工厂成批生产。设计选择时常需考虑的因素有寿命、负荷、精度、游隙(径向和轴向)、极限转速、摩擦力矩、调心性能、预紧和刚性、振动和噪声等。
说明:补充资料仅用于学习参考,请勿用于其它任何用途。
参考词条