1) position detecting error
位置检测误差
1.
The experimental calibration system is built in a multipurpose instrument microscope for reducing the position detecting error of this sensor.
分析了改进表面分流型二维位置敏感探测器(PSD)的工作原理及信号调理电路,针对PSD位置检测误差大的缺点,设计了利用万能工具显微镜进行标定的实验系统,运用误差理论对传感器在A区和B区的X向及Y向位置测试数据进行了校正。
2) phase error detection
相位误差检测
1.
Improved algorithm for DS-QPSK phase error detection and its digital implementation
DS-QPSK相位误差检测算法改进与数字化实现
2.
This paper,in combination with high-speed satellite communication application,first studies the structural model of the carrier recovery loop based on maximum posteriori probability estimation principle,and then analyzes in-depth the features of the adopted carrier phase error detection algorithm,and finally describes the simulation .
结合高速卫星通信的应用,文中首先对基于最大后验概率估计准则载波恢复环的结构模型进行了研究,然后对所采用的载波相位误差检测算法的特性进行了深入的分析,最后对载波恢复系统中尤其重要的环路鉴相特性进行了计算机仿真,给出了环路性能试验分析结果。
3) position error
位置误差
1.
Method for auto modification of position error of scanner;
扫描仪位置误差自动修正方法
2.
The paper analyses difficulties and characteristics in machining bearing hole of canular forked shaft and measuring its position error;and it designs equipment for machining and measuring this hole.
在叉头套加工过程中,轴承孔位置误差的测量和控制是十分重要。
3.
Measurement and compensation of volumetric position errors for NC machine tools are important approach for quality assurance and higher accuracy.
机床空间位置误差的测量和补偿是提高加工精度的重要手段。
4) Positional error
位置误差
1.
The article establishes an optimal synthesis model based on the positional error between the practical generated paths and the desired paths, gets a synthetic result by optimization toolbox of MATLAB5.
基于连杆点实际生成的轨迹曲线与预期的理想轨迹曲线间的位置误差建立优化综合模型 ,为克服传统优化技术局限性 ,利用MATLAB中Optimization工具箱获得综合结果 ,得到一实现两平行直线轨迹的平面五连杆机构 综合实例结果表明了本方法的有效
2.
An analysis is made of the positional error of the link mechanism through the matrix theory.
利用矩阵理论对连杆机构的位置误差进行了分析，给出了有关的计算公式，并对铰链四杆机构进行了实际计算，其结果对各类连杆机构都具有普遍适用性。
3.
According to rotationplasty and move transforming characteristics of robot joints,this paper established the accurate postural and positional error model of robot,which is a homogeneous matrix.
机器人执行部件的位置误差(或精度),是反映机器人性能的一个重要指标。
5) error detection
误差检测
1.
Therefore error detection and error proofreading are the primary task of dealing with errors.
本文讨论了基于主元分析(PCA)的显著误差检测与校正原理,运用Q统计方法,结合贡献图对某电厂热风送粉系统风粉浓度软测量中可能出现的显著误差进行了仿真分析,结果表明,基于PCA主元分析的显著误差检验和校正方法在风粉浓度软测量工业应用中可行。
2.
This subject is about thermal deformation error detection and compensation of an YKX3132G six axes CNC gear-hobber machine's worktable in X axis direction.
根据理论分析,笔者在现有实验条件下,分别基于单片机与PCI数据采集卡,设计出两种误差检测与补偿系统。
6) error inspection
误差检测
1.
In view of the problem of difficult to measure and inspect spatial cams,a simple,rapid and applied error inspection method for spatial cams is provided in this paper.
本文针对空间凸轮难以精密测量及检测的问题,提出了一种简单、快速与实用的空间凸轮廓面加工误差检测新方法。
补充资料：设备的安装位置的检测与调整
设备的安装位置的检测与调整   | ||
|
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条