1) transverse end effect
横向边端效应
2) transverse edge effect
横向端部效应
3) transverse end-effect
横向边缘效应
1.
Two groups of equivalent coefficient for transverse end-effects are derived, i.
进而又推导出直线感应电动机横向边缘效应两组等效系数公式（电流密度系数ＫＪ、电阻率系数Ｋρ、有功功率系数ＫＰ、无功功率系数ＫＯ），为直线感应电动机的设计计算提供了较为简捷、准确的计算横向边缘效应的方法。
4) transverse edge effect force
横向边缘效应力
5) end effect
边端效应
1.
Dynamic end effect of single sided linear induction motor (SLIM) is caused by the eddy current in the secondary with the increase of SLIM speed.
研究直线感应电动机动态边端效应特性可知,电机次级涡流是产生动态边端效应的主要原因。
2.
For reducing detent force of permanent magnet linear synchronous motors(PMLSM) resulting from slot effect and end effect.
为了最小化由边端效应与齿槽效应引起的永磁直线同步电机(PMLSM)的推力波动,提出了一种数理分析相结合的优化设计方法。
3.
Considering the end effect of linear induction motor (LIM), a simulation model of linear induction motor vector control system with the rotor flux oriented frame (RFO) was established.
考虑到直线感应电机的边端效应 ,根据矢量变换控制原理 ,利用Simulink构造了直线感应电机转子磁场定向下的矢量控制系统的模型 ,并进行了仿真 ,结果证明了仿真的有效
6) lateral effect
横向效应
1.
In order to ascertain the pivotal factors affecting the lateral effect of PELE,a series of experiments of PELE projectiles impacting steel plate were made with different jacket materials,filling materials,impact velocities and impact angles.
试验结果表明,弹体采用压拉比高的材料时,PELE横向效应明显;在试验速度范围内,随着速的提高,PELE破片数量增多,横向效应增强;装填物材料对横向效应的主要影响因素是泊松比和弹性模量,而不是密度;在0°~45°范围内,随着角的增大,PELE横向效应增强。
2.
With impact velocity between 400～900 m/s,after PELE perforates the target,the amount of the debris and the covering area increase and the lateral effect is intensified.
为了分析弹丸着靶速度与PELE横向效应之间的关系,在弹靶系统一定的条件下,就不同弹丸着速对PELE横向效应的影响进行了试验。
3.
To analyze the influence of target thickness on the lateral effect of PELE(Penetrator with enhanced lateral effect),by changing target board thickness,simulations and experimentations are carried out on PELE impacting target perpendicularly in the same speed.
为了分析靶厚对横向效应增强型侵彻体(PELE)作用效果的影响,采用改变靶板厚度的方法,对PELE以固定速度垂直撞击靶板进行了数值仿真和实验验证。
补充资料：横向效应
见电阻应变计。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条