1) cool extruding finishing
冷挤压光整加工
1.
The working principle and surface forming mechanism of the cool extruding finishing using the carbide turning tool are analyzed, and rational extruding parameters are presented.
分析了用硬质合金车刀进行冷挤压光整加工的工作原理及挤压表面强化机理 ,并给出了合理的挤压工艺参
2) extrusion finishing
挤压光加工
3) extrusion
[英][eks'tru:ʒən] [美][ɛk'struʒən]
挤压加工
1.
Primary study on coffee substitute prepared by extrusion of wheat germ and soybean
大豆和麦胚芽挤压加工咖啡替代物的初步研究
2.
This paper mainly discussed the effects of nutritional properties on extrusion process,and described the effects of extrusion process parameters such as feed speed,feed moisture content,barrel temperature on protein,starch,fat,vitamins,available lysine,activity of urease,revealed the effects of extrusion process on nutritional quality from another perspective.
分析挤压加工过程中,挤压工艺参数对食品营养品质的影响。
3.
Triturated food prepared by extrusion of wheat germ and cornmeal was studied with referent indexes of sensory characteristics.
结果表明:麦胚芽经挤压加工后粗纤维含量下降达46。
4) extrusion process
挤压加工
1.
This article compares extrusion process with conventional processes in some peducts .
本文通过将挤压蒸煮方法与传统加工方法在一些产品的加工方面进行对比，显示了挤压加工的优势和经济性，指出食品挤压加工是今后食品工业发展的一个方向。
2.
A kind of aluminum alloy profile with high conductivity and high yield strength was produced by extrusion process test,its conductivity is up to 60%IACS,yield strength(σ0.
用正交试验法对比分析了纯铝合金中添加Fe、Cu、Mg、Zn对其电导率及屈服强度的影响程度;并由此进行成分配比,通过挤压加工试验,研制生产出一种高电导率高屈服强度铝合金型材,H112状态电导率达60%IACS左右、屈服强度σ0。
5) extruding processing
挤压加工
1.
The influence of extruding processing on the water retention capacity of insoluble diet fiber(IDF)was studied and the optimum parameters were obtained:material water content 30%;processing temperature 140 ℃;screw speed 100 r/min.
为此,研究了挤压加工对米糠中IDF持水力的影响,并获得了最优挤压加工参数组合为:原料含水量30%,挤压温度140℃,螺杆转速100r/min。
6) cold extruding technology
冷挤压工艺
1.
After using the cold extruding technology, abained good effect.
采用冷挤压工艺取代传统的机械加工工艺,取得了较好的效果。
2.
the advantages of the titanium alloy hexagon locking-nuts with flange with cold extruding technology replacing hot extruding working method are introduced.
对钛合金六角法兰面自锁螺母进行了工艺分析、制订了冷挤压工艺路线、计算了毛坯尺寸及冷挤压力。
3.
The advantages of the reel internal gear with cold extruding technology replacing traditional metal cutting working method were narrated, and the technological for the reel internal gear was analyzed.
叙述了卷筒内齿轮用冷挤压工艺代替传统的金属切削加工方法的优点,并对卷筒内齿轮进行了工艺分析。
补充资料：冲击挤压(见冷挤压)
冲击挤压(见冷挤压)
impact extrusion
ehongji jiya冲击挤压(impaet extrusion)见冷挤压。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条