1) thermal time
热时间
1.
) with different vernalization development characteristics were used to investigate the effects of accumulated temperature before wintering on spike differentiation by vernalization treatments and sowing dates experiment,and the effects were expressed by thermal time.
以3个春性、半冬性和冬性小麦品种为材料,采用分期播种和春化处理,以热时间为尺度,研究了冬前积温对不同春化发育特性小麦品种幼穗分化进程及主要穗分化期累积GDD(生长度日,growingdegree days)的影响。
2.
The thermal times for 50% germination were 116 degree days ( ℃d) at 15℃, 45 ℃d at 25 ℃ and 60 ℃d at 30℃, respectively.
在１５℃、２５℃和３０℃中，５０％萌发需要的时间分别是１８６ ｈ、４３ ｈ和 ４８ ｈ；５０％萌发需要的热时间（ｔｈｅｒｍａｌ ｔｉｍｅ）分别为１１６℃ｄ、４５℃ ｄ和６０℃ｄ；当萌发温度为３５℃时，种子的萌发速率和萌发率被严重地抑制，在整个萌发过程中未出现５０％萌发的时间，以及５０％萌发需要的热时间远远大于２１０℃ｄ。
2) heating time
加热时间
1.
Analysis to the influences of heating time on the Bell-type furnace;
浅析罩式退火炉加热时间的影响因素
2.
The equipment is composed of extrusion,liquid pressure station,intermediate frequency heating system(another introduction),cooling system,electric cabinet,operation bed,kcn-4s/w add-subtract counter can be used as high precise timer to control the tube heating time of the GTR type intermediate frequency respond heating stove expends to the tubes.
设备由挤压主机、液压站、中频加热系统(另外介绍)、冷却系统、电气柜、操作台组成,其中KCN-4S/W加减计数器可以用作高精度的定时器来控制GTR型中频感应加热炉对管子的加热时间。
3.
Researches show that when the air is preheated to 900 ℃ and oxygen concentration is enriched to 54%,the heating time decreases by 38%,the product rate increases by 61%,thermal efficiency increases by 30.
研究表明:在预热900℃和含氧体积分数为54%条件下燃烧与传统燃烧相比,加热时间可缩短38%,生产率可提高61%,热效率可提高30。
3) soaking time
均热时间
1.
Effect of soaking time on the dissolution of microalloyed elements in high-strength steel containing Ti and Nb;
均热时间对含Ti、Nb微合金元素高强钢固溶规律的影响
2.
The usage of HFH furnace is given and a introduction of calculation of soaking time and purging time in HFH furnace is discussed based on HPH furnace of Baosteel.
在冷轧钢材的工业生产中,罩式炉退火是一个重要的环节,本文讲解了新型的HPH罩式炉的作用,并以宝钢的HPH罩式炉为背景,介绍了控制中最关键的均热时间和保护气氛冲洗时间的计算方法。
4) heat protection time
防热时间
5) preheating time
预热时间
1.
Determination of optimal preheating time during thermal conductivity measurement with steady-plane-wall system;
稳态平板导热仪最优预热时间的确定
6) Hot pressing time
热压时间
1.
They can greagly shorten the hot pressing time and improve the qualities of products.
蒸汽喷射热压法是能显著缩短热压时间、提高产品质量、前途远大的一门实用性技术 ;蒸汽喷射热压法的应用 ,将使厚、特厚板及低密度板的制造成为可能。
补充资料：热缺血时间
热缺血时间
warm ischemia time
指断肢离断后到断肢冷藏开始的时间称为热缺血时间。肢体离断后，虽然血流中断，肢体组织仍继续进行代谢，消耗残存的氧分。氧分消耗完后，仍可进行无氧代谢，但新陈代谢产物无法清除，引起酸中毒，加上代谢必需的养料和酶系统消耗，最后难免死亡。一般肌肉组织最敏感，缺血4～6h后，便无法再植。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条