1) cold shock treatment
冷冲击处理
1.
Through comparing the variations of their contents after different cold shock treatments and the chilling injuries (CI), the regularity of phytohormone variations and the relationship between phytohormones level and the chilling tolerance of Nai-plum fruits during the cold storage were discussed.
通过比较了不同冷冲击处理对内源激素的影响以及贮藏过程中激素的变化,并结合冷藏过程中冷害发生情况,初步探讨了各处理在冷藏过程中内源激素变化的规律及其与柰李果实抗冷性的影响。
2.
The results showed that cold shock treatment refrained desiccation, and the degree of refrainment was increasing with the duration of cold shock treatment.
）为材料，以０℃的冰水混合物为冷却介质，研究了不同冷冲击处理（１ｈ，２ｈ，３ｈ，４ｈ）对贮藏期间银杏硬化的影响结果表明，冷冲击处理能显著地控制白果的硬化，硬化率随处理时间的延长而降低
3.
The experiment showed that cold shock treat-ment refrained the activity of polygalacturonase,and the degree of refrainment was increasingwith the time of cold shock treatment.
本实验以绿熟期的渝抗二号番茄（ＶａｒＣｏｍｍｕｎｅｂａｉｌｅｙ）为材料，０℃的冰水混合物为冷却介质，研究了不同冷冲击处理时间（１ｈ，２ｈ，３ｈ，４ｈ）对贮藏期间多聚半乳糖醛酸酶（ＰＧ）活性的影响。
2) heat-shock treatment
热冲击处理
1.
An ethanol-resistant and heat-resistant mutant (UV-7-36-12-17) of Saccharomyces cerevisiea was successfully bred by the techniques of UVB radiation culture and heat-shock treatment,which could grow well in the triangular flask under the conditions of 16 %(v/v)ethanol content,temperature at 36 ℃,and alcohol content reached 14.
通过UVB照射培养和热冲击处理,成功地选育到一株36℃下在含16%(v/v)酒精的培养基中生长良好,三角瓶发酵酒精度达到14。
3) hydrodynamic shock waves process
冲击波处理
1.
Rigor mortis , ageing, tenderization mechanism,pulsed electrical current-termed electrical stimulation, calcium chloride processing, exotic proteinase processing, stretching techniques , pH control processing, high pressure process, hydrodynamic shock waves process etc.
综述了肉类尸僵、成熟、嫩化机理、电刺激、钙处理、外源酶处理、机械嫩化、pH处理、高压处理、冲击波处理等影响肉类嫩度与品质的因素及嫩化的技术理论和方法。
4) laser shock processing
激光冲击处理
1.
Application of laser shock processing on turbine engines;
激光冲击处理技术在发动机上的应用
2.
The research state of laser shock processing to improve the mechanical properties of aeronautical materials;
激光冲击处理提高航空材料机械性能的研究现状
3.
Laser Shock Processing of 40Cr Steel and Numerical Simulation of Residual Stress Field Induced by LSP;
激光冲击处理40Cr钢及其残余应力场数值模拟
5) ultrasonic impact treatment
超声冲击处理
1.
Influence of ultrasonic impact treatment on microstructure of 2A12 aluminum alloy welded joint;
超声冲击处理对2A12铝合金焊接接头组织的影响
2.
The results shows that ultrasonic impact treatment can change tensile stress into pressed stress,the mean longitudinal residual stress before and after impact treatment of 45# steel and 22SiMn2TiB steel are 169?-63?296?-49MPa respectively, the descend ratio ar.
对45号钢和22SiMn2TiB钢焊缝的焊趾处进行超声冲击处理,并测量处理前、后的残余应力。
3.
The specimens of the welded joints were treated with ultrasonic impact treatment(UIT)and compared with the as-welded ones.
采用超声冲击处理(UIT)方法对焊接接头进行处理,并将冲击态接头与焊态接头进行了对比。
6) ultrasonic peening treatment
超声冲击处理
1.
The variation of weld toe geometric shape and hardness was measured before and after ultrasonic peening treatment with toolmaker′s microscope and Vickers hardness tester.
使用工具显微镜和维氏硬度计测量了超声冲击处理前后焊趾区的几何形状与硬度的变化,并应用疲劳缺口系数的概念及Dang Van准则,对超声冲击造成的焊趾区几何形状的变化及残余压缩应力对接头疲劳性能改善的影响行为进行了研究。
2.
To improve the fatigue strength of T-shape tubular joints, the ultrasonic peening treatment is proposed in the fatigue contrast tests of low carbon steel and austenite stainless steel 1Cr18Ni9Ti at the same strength level.
结果表明:超声冲击处理低碳钢后疲劳强度提高67％左右,疲劳寿命延长了22-45倍;超声冲击处理奥氏体不锈钢1Cr18Ni9Ti疲劳强度提高69％左右,疲劳寿命延长了21-30倍。
补充资料：冲击挤压(见冷挤压)
冲击挤压(见冷挤压)
impact extrusion
ehongji jiya冲击挤压(impaet extrusion)见冷挤压。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条