1) book size
幅面尺寸
1.
An investigation on the formats and book sizes of 428 sci-tech periodicals;
428种科技期刊开本及幅面尺寸现状调查
2.
To further improve conformity to standard paper format in sci-tech journals, the GB/T 788-1999 standard is used to gauge book sizes of 808 16-format journals in science and technology published in China.
为进一步提高科技期刊幅面尺寸的标准化水平,以GB/T 788—1999为依据,对808种采用16开本的科技期刊的幅面尺寸进行了调查。
2) width size
幅面尺寸
1.
An special investigation is carried out based on 45 published university journals in 2008 in Zhejiang, only nine of which are in conformity with the principle of GB/T788-1999---Format and Width Size of Magazines and Jornals——in width size, accounting for 20% of the total.
对2008年出版的45种公开发行的浙江省高校学报的幅面尺寸进行了调查。
2.
The problems and the causes of failing to meet the national standards for University journals in format and width size are analysed in this paper,and some suggestions on how to achieve the standardization are put forward.
对2008年出版的399种公开发行的高校学报的开本及幅面尺寸进行调查。
3) sheet dimension
图幅尺寸
4) cross-sectional dimension
断面尺寸
1.
Continuous measurement for cross-sectional dimensions of extruded tread on line by laser system;
激光在线测量连续挤出胎面断面尺寸
2.
The cross-sectional dimension and taper are the most important data in the design of the mould.
结晶器是连铸机中一个非常关键的设备,结晶器的断面尺寸和锥度是结晶器设计中最重要的参数。
5) section size
断面尺寸
1.
This paper introduces a method for calculating the ordinary pouring system section size of large injection mold.
介绍了一种大型塑料模浇注系统断面尺寸的设计与修正方法。
2.
In this paper,a method for calculating the ordinary pouring system section size of large injection mold is introduced.
介绍一种计算大型注射模普通浇注系统断面尺寸的方法;采用这种方法,既可直接用来确定注射模普通浇注系统的主流道、分流道、浇口的断面尺寸,也可用来校核凭经验设计的浇注系统的断面尺寸的正确性,解决一些难以解决的塑料模具设计问题,以达到提高产品质量、缩短模具制造周期的目的。
6) section size
截面尺寸
1.
Analysis of factors for controlling section size of RC frame columns in seismic zone;
钢筋混凝土抗震框架柱截面尺寸控制因素分析
2.
Optimizing the section size and chosing the nearest shape are the development direction of continuous casting.
论述了连铸方坯对不同产品用途、规格所需的压缩比,分析了矩形连铸坯截面优于方形坯;指出优化截面尺寸,选择近终形截面连铸是发展方向。
3.
During design phase of gravity retaining wall, relatively correct retaining wall section size can be obtained by repeated trial calculations.
在重力式挡土墙设计中,设计者往往要经过反复试算才能得到相对合理的挡土墙截面尺寸,为避免反复计算的麻烦,对尺寸问题进行了探讨。
补充资料：工程图标准尺寸及坐标尺寸
标准标注类型，是我们常用的标注类型。而坐标标注是便于数控加工采用的另一中标注形式。PRO/E可以将两种标注方式进行转换。
· 3.2 标准标注到坐标标注的转换
注意： 转化为坐标标注的尺寸必须是线性标注的，下列尺寸不能转化为坐标标注：
- 被显示成线性尺寸的直径
- 中心线尺寸
- 选择MODIFY DRAW > Dim Params > Dim Type > Ordinate Dim > Create Base.
- 选择作为参考基准线的尺寸
- 选择基准的引出线，该点为0点
- 选择 MOD DIM TYPE > Lin to Ord .
- 选择线性尺寸：注意：必须选择具有相同基准的尺寸
========>>>>
1. 选择 DIM PARAMS > Diam Dim Type .
2.点击Ord to Lin 
3.选择尺寸即可
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条