1) erosion and self-combustion mechanism
腐蚀自燃机理
2) corrosion mechanism
腐蚀机理
1.
Corrosion mechanisms and desalination treatments of marine iron artifacts;
海底打捞铁质文物的腐蚀机理及其脱氯方法
2.
The corrosion mechanism and anticorrosion methods of CO_2 removal system in hydrogen produced unit;
制氢脱碳系统腐蚀机理与防腐措施
3.
Study on the corrosion mechanism of the dam concrete by natural water;
天然水对碾压混凝土的腐蚀机理探讨
4) corrosion mechanisms
腐蚀机理
1.
The corrosion mechanisms of soft water is theoretically studied by the tests of soft water of different qualities and their relationship with chlorine ions and alkalinity based upon the corrosion of soft water system of Jingmen Petrochemical Company/SINOPEC.
针对中国石化股份有限公司荆门分公司软化水系统出现的腐蚀问题,通过对不同的软化水水质与氯离子、碱度等的关系试验,从理论上探讨了软水的腐蚀机理,说明不同的水质腐蚀状况不尽相同。
2.
The main process and equipment of methanol heat exchanger EA - 206 in ammonia unit are introduced, and corrosion mechanisms is studied.
介绍了合成氨装置中主甲醇换热器EA-206的工艺和设备情况,并对其腐蚀机理进行了分析。
3.
1 Gas Production Plant of PetroChina Changqing Petrochemical Company analyzed the corrosion mechanisms of furnace and its impact factors based upon the operating conditions of the furnace.
中国石油天然气股份有限公司长庆石化分公司第一采气厂在对加热炉现场使用工况条件、运行现状调查的基础上,分析研究了加热炉腐蚀机理及其影响因素。
5) erosion mechanism
腐蚀机理
1.
At the asme time,erosion mechanism of CO2 and H.
同时,就CO2和H2S对水泥石的腐蚀机理进行了分析探讨。
2.
The paper analyzed the erosion mechanism and protection method steel gates that are widely used in spillways of large and medium sized reservoirs.
大中型水库溢洪道多采用钢闸口 ,它的腐蚀问题都不同程度存在 ,分析了钢闸门的腐蚀机理与防护办
6) corrosion principle
腐蚀机理
1.
Research on liming-up corrosion principle and settling countermeasure of highway tunnel;
公路隧道衬砌腐蚀机理与处治对策研究
2.
This paper introduces the basic situation of the leakage accidence of hot-water boiler, analyzes on the causes of the leakage accidence of hot-water boiler and its corrosion principle, and puts forward some measures for preventing the corrosion.
介绍了热水锅炉泄漏事故的基本情况,对引起热水锅炉泄漏的原因及其腐蚀机理进行了分析,并提出了防止腐蚀发生的措施。
补充资料：自燃点和自燃温度
分子式：
CAS号：
性质：又称自燃点和自燃温度。在规定条件下，可燃物质不需外来火源即发生燃烧的最低温度。中国规定气体、蒸气危险物质按引燃温度分为6组：引燃温度T>450℃为T1组、300℃<T≤450℃为T2组、200℃<T≤300℃为T3组、135℃<T≤200℃为T4组、100℃<T≤135℃为T5组。85℃<T≤100℃为T6组。粉体、纤维危险物质按引燃温度分为3组：引燃温度T>270℃为Tll组、200℃<T≤270℃为T12组、140℃<T≤200℃为T13组。
CAS号：
性质：又称自燃点和自燃温度。在规定条件下，可燃物质不需外来火源即发生燃烧的最低温度。中国规定气体、蒸气危险物质按引燃温度分为6组：引燃温度T>450℃为T1组、300℃<T≤450℃为T2组、200℃<T≤300℃为T3组、135℃<T≤200℃为T4组、100℃<T≤135℃为T5组。85℃<T≤100℃为T6组。粉体、纤维危险物质按引燃温度分为3组：引燃温度T>270℃为Tll组、200℃<T≤270℃为T12组、140℃<T≤200℃为T13组。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条