说明:双击或选中下面任意单词,将显示该词的音标、读音、翻译等;选中中文或多个词,将显示翻译。
您的位置:首页 -> 词典 -> 计时点
1)  timing point
计时点
1.
A theoretic analysis of the selection of timing point of the plane single pendulum from the non-linear perspective;
平面单摆计时点选取的非线性理论分析
2)  terminal timing
终点计时
1.
Design of terminal timing system based on color CCD;
彩色CCD终点计时系统的设计
3)  starting time
计时起点
1.
Defining starting time in the experiments of fall-ball method to measure the coefficient of viscous liquids;
用落球法测液体的粘滞系数实验中计时起点的确定
2.
Determination of starting time in method of dropping spherule for measuring the coefficient of viscosity;
用落球法测液体粘度计时起点的确定
4)  ticker-timer
打点计时器
1.
Making ticker-timer using transfusion set;
用输液器制作“打点计时器”
2.
Measuring the Young modulus using ticker-timer as excitation source
用打点计时器做激发源测量杨氏模量
5)  zero time reference
零时参考点,计时起点
6)  electromagnetic ticker timer
电磁打点计时器
1.
The paper introduces the new experimental design of electromagnetic ticker timer to demonstrate the phenomena of driven oscillations and resonance,wave diffusion,interference,diffraction and stationary wave.
介绍电磁打点计时器的新的实验方案,用来演示受迫振动和共振现象,演示波的传播、干涉、衍射和驻波等实验现象;还介绍利用电磁打点计时器制作频闪光源的简单方法,使被淘汰的老仪器焕发新的生机。
补充资料:闭式单点、双点压力机
代码:00413
设备名称:闭式单点、双点压力机
型号规格:公称力≥800kN
计量单位:台
主要参数内容
国际先进国内先进国内一般国内落后评定方法及说明
(一)加工精度
    参照GB10924-89、GB10933-89、JB5200-91
1、滑块下平面对工作台上平面的平行度(mm)
30%精度储备20%精度储备达到规定值大于规定值 
0.02+0.10/100×滑块下平面的被测长度
     
2、滑块行程对工作台上平面的垂直度
30%精度储备20%精度储备达到规定值大于规定值 
0.05+0.02/100×滑块行程长度
     
(二)结构性能
     
1、离合器、制动器接通率,当滑块行程次数≤16次/分时为70%,≤25次/分时为60%,≤45次/分时为50%
大于规定值10%大于规定值达到规定值达不到规定值 
2、液压超负荷保险装置、微调装置、吨位指示器
全部具有全部具有部分具有没有 
(三)噪声dB(A)
     
1、公称力≤400kN
≤85≤87≤88>88 
2、公称力>400kN
≤87≤88≤90>90 
说明:补充资料仅用于学习参考,请勿用于其它任何用途。
参考词条