说明:双击或选中下面任意单词,将显示该词的音标、读音、翻译等;选中中文或多个词,将显示翻译。
您的位置:首页 -> 词典 -> 相似点
1)  similarities [英][,simi'læriti]  [美][,sɪmə'lærətɪ]
相似点
1.
However, a careful study may reveal the similarities between their ideas, such as the opposed objects, definitions of sign and semiotics, the meaning, classification and functions of signs, and the dependency of signs.
国内符号学研究往往把皮尔士和索绪尔分别当作现代符号学的两支源头,认为二者观点互不相干,然而经仔细研究,二者的符号学观中却有惊人的相似之处,具体体现在其反对的对象,符号及符号学界定,符号意义,作用,分类,发展及符号的依赖关系上,了解这些相似点,有助于国际符号学交流,统一认识,推动符号学的发展。
2.
Therefore,the present paper explores the similarities and differences between English and Chinese discourse with the aim to serve Sino-British cultural exchange better.
通过探讨英汉语篇的相似点与差异,更好地为现今中英文化的交流服务。
2)  similarity [英][,sɪmə'lærəti]  [美]['sɪmə'lærətɪ]
相似点
1.
Analysis of Similarity between Nexus and Dou "读" and Its Practical Meaning;
“联系式”(Nexus)和“读”的相似点及其引发的思考
2.
This paper deals with this problem and points out the necessity of distinguishing the tenor,the vehicle and the similarity for the comprehension of a metaphorical utterance.
文章探讨了国内英语修辞学界对于比喻的本体、喻体研究的不足 ,提出本体、喻体的界定 ,判断的必要性及方法 ,同时对比喻中本体、喻体及相似点的隐现情况作出了分
3)  similar point
相似点
1.
Using Similar points of the analogy detween things in the category of the same property and of the different ones,between things visable and inuisable and between things of different catngories of sense organs,this essay illustrates the key role in seeking the similar point in the using of analogy.
本文通过对同一属性范畴事物 ,不同属性范畴事物 ,无形与有形事物 ,不同感官范畴事物间比喻相似点的运用 ,说明了寻找相似点在比喻中的重要作
4)  similar node
相似节点
1.
According to the requirement for adaptability in distributed embedded system such as UAVs, wireless sensor network and so on, some common methods are proposed to define similar nodes, compute their similarity degree, discover similar nodes and deploy the other’s tasks on them automatically.
提出嵌入分布式系统中相似节点的自动发现机制以及相似节点上的任务自动部署方法。
5)  point-similarity
点相似
6)  resemblance [英][rɪ'zembləns]  [美][rɪ'zɛmbləns]
n.相似;相似点;相似物
补充资料:闭式单点、双点压力机
代码:00413
设备名称:闭式单点、双点压力机
型号规格:公称力≥800kN
计量单位:台
主要参数内容
国际先进国内先进国内一般国内落后评定方法及说明
(一)加工精度
    参照GB10924-89、GB10933-89、JB5200-91
1、滑块下平面对工作台上平面的平行度(mm)
30%精度储备20%精度储备达到规定值大于规定值 
0.02+0.10/100×滑块下平面的被测长度
     
2、滑块行程对工作台上平面的垂直度
30%精度储备20%精度储备达到规定值大于规定值 
0.05+0.02/100×滑块行程长度
     
(二)结构性能
     
1、离合器、制动器接通率,当滑块行程次数≤16次/分时为70%,≤25次/分时为60%,≤45次/分时为50%
大于规定值10%大于规定值达到规定值达不到规定值 
2、液压超负荷保险装置、微调装置、吨位指示器
全部具有全部具有部分具有没有 
(三)噪声dB(A)
     
1、公称力≤400kN
≤85≤87≤88>88 
2、公称力>400kN
≤87≤88≤90>90 
说明:补充资料仅用于学习参考,请勿用于其它任何用途。
参考词条