1) ECAP
等径角变形
1.
Strengtheningtechniques including equal channel angular pressing (ECAP) at 400℃via route Bc, extrusion at 300℃with extrusion ratio of 9、ageing at 250℃were applied to theMg-.
％)镁合金作为研究对象，通过400℃下Bc方式等径角变形、300℃下挤压比为9的常规挤压和250℃时效处理三种加工工艺相结合的工艺对Mg-12Gd-3Y-0。
2.
The typical eutectoid alloy Cu-Al is chosen to investigate the microstructure change rule of the pre-eutectoid and eutectoid phases in it by implementing proper heat treatment and equal channel angular pressing(ECAP).
以典型的共析体系合金Cu-Al合金为研究对象,对其进行了恰当的热处理和等径角变形(ECAP)处理,研究了该合金中先共析相与共析相的组织变化规律。
2) Equal channel angular pressing
等径角变形
1.
Equal channel angular pressing at room temperature was used to impose high strain(24) into the pure copper.
采用等径角变形(ECAP)成功地实现了室温下纯铜高道次(24)ECAP变形，获得了超细晶铜，研究了高道次变形过程中的组织转变以及变形储存能与再结晶温度变化关系，同时对高道次变形后力学性能变化进行了深入研究分析。
3) equal channel angular pressing
等径角挤压变形
1.
Influence of Original Structure on Equal Channel Angular Pressing Deformation of 304L Extra-Low Carbon Stainless Steel;
原始组织对304L超低碳奥氏体不锈钢等径角挤压变形的影响
2.
The microstructure evolution of as-cast 304L austenitic stainless steel during equal channel angular pressing(ECAP) from 1-4 passes was investigated.
研究了经1~4道次等径角挤压变形(ECAP)后,铸态304L奥氏体不锈钢微观结构的演变,同时测定了ECAP变形后的力学性能。
3.
The microstructure and properties of austenitic stainless steel produced by forging or equal channel angular pressing(ECAP) and followed by recrystallization annealing treatment were investigated.
在试验的基础上研究了经2种塑性变形(锻造、等径角挤压变形)的奥氏体不锈钢完全再结晶后的组织与性能。
4) equal channel angular pressing
等径角挤
1.
The microstructure evolution of pure aluminum in different equal channel angular pressing (ECAP) routes was investigated.
研究了纯铝在 3种 (A、B和C)不同等径角挤工艺中的显微组织演化。
2.
The computer simulation and experiments for the deformation behavior of pure Al in equal channel angular pressing (ECAP) process were conducted by finite element method (FEM) and coordinate network.
通过有限元模拟和坐标网格,对纯铝等径角挤过程的变形行为进行了模拟和试验。
5) equal channel angular pressing(ECAP)
等径弯曲通道变形
1.
The equal channel angular pressing(ECAP) of 2J4 alloy was studied at room temperature with route A in which the sample was not rotated after pressing one pass and entered directly the next pass.
借助光学显微镜和透射电镜对2 J4合金等径弯曲通道变形(ECAP)组织进行了研究。
6) ECAP
等径弯曲通道变形
1.
The influence of Equal Channel Angular Pressing(ECAP) deformation on the microstructure and magnetic properties of a semi-magnetic alloy,2J4,was studied.
研究了等径弯曲通道变形(ECAP)对2J4合金显微组织和磁性能的影响。
2.
3 μm after fourth pass and the grain size does not decrease further after 4 pass of ECAP.
研究了室温下C方式等径弯曲通道变形(ECAP)对超低碳钢组织及性能的影响。
3.
Equal Channel Angular Pressing(ECAP) is a new processing procedure fabricating ultrafine grain material,whose basic principle is that sample is embedded into the bending passage which has the same cross-section shape.
等径弯曲通道变形(ECAP)是制备超细晶材料的新工艺,其基本原理是将试样放入横截面形状完全相同、并成一定角度的弯曲通道中,试样在压力作用下通过通道时,在通道弯曲处产生一定量均匀的纯剪切变形,最终获得很高的变形量,使材料组织发生明显细化。
补充资料：胎圈变形、弯钢圈、钢圈变形、口弯等
分子式：
CAS号：
性质：又称胎圈变形、弯钢圈、钢圈变形、口弯等。指轮胎胎圈表面局部高低不平的现象。 胎圈底部 bead base 又称胎圈基部。指轮胎与轮辋胎圈座接触的部位。其作用是保持胎圈与轮辋底部相着合。
CAS号：
性质：又称胎圈变形、弯钢圈、钢圈变形、口弯等。指轮胎胎圈表面局部高低不平的现象。 胎圈底部 bead base 又称胎圈基部。指轮胎与轮辋胎圈座接触的部位。其作用是保持胎圈与轮辋底部相着合。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条