1) relatively static structure

相对静态结构
2) Static structure

静态结构
1.
Organization pattern,static structure and dynamic behavior of Workorder Management System(WMS) are studied based on UML for equipment maintenance of petrochemical plant.
针对炼化企业设备维护的工单管理系统,分别进行组织模式、静态结构和动态行为的UML建模分析。
2.
An application of home security system design using UML2 is presented,analyzing the static structure and dynamic behavior of the system,modeling system from an overall point by UML diagram such as class diagram,sequence diagram,state diagram,to illustrate real-time analysis and design pr.
结合一个使用UML2为家庭安全系统设计的例子,着重分析了系统的静态结构和动态行为,通过类图、顺序图、状态图等UML图描述系统的方法从整体上对系统建模,说明实时系统分析与设计过程。
3.
Secondly, the author expresses the static structure of this system by introducing its class definitions and relationships.
文章主要介绍了一种进化仿真框架——仿生系统SimBioSys,首先介绍了这种仿生系统的概念,其次通过介绍它的类关系和定义揭示了它的静态结构,最后提出这种仿生系统的动态循环结构,并简单介绍了仿生系统在科学研究中的应用。
4) morphological structure

相态结构
1.
Effects of coupling agents on curing characteristics and physical-mechanical properties of the two kinds of composites were investigated,and the morphological structure of the composites were observed by scanning(electron) microscope.
采用乳液共混法制备了淀粉/丁苯橡胶(SBR)以及间苯二酚甲醛树脂(RF)改性淀粉/SBR复合材料,考察了偶联剂对2种复合材料硫化特性、力学性能的影响,并用扫描电镜观察了其相态结构。
2.
The morphological structure of dynamically vulcanized thermoplastic(elastomer)(TPV) ethylene propylene diene monomer(EPDM)/polypropylene(PP) was investigated with scanning electron microscope.
用扫描电镜研究了三元乙丙橡胶(EPDM)聚/丙烯(PP)动态硫化热塑性弹性体(TPV)相态结构的形成过程,探讨了交联密度、制备工艺、螺杆转速对EPDM/PP TPV相态结构的影响。
3.
The morphological structures of NBR/PP TPV were analyzed.

苄酯4种增塑剂对丁腈橡胶(NBR)聚/丙烯(PP)热塑性硫化胶(TPV)邵尔A硬度、耐油性能和流变性能的影响,并用透射电镜分析了4种增塑剂对NBR/PP TPV相态结构的影响。
5) Phase Structure

相态结构
1.
Study on microstructure and phase structure of SBS modified asphalt;

SBS改性沥青显微结构及相态结构研究
2.
The phase structure analysis on CPVC/CR-MMA graft modificated adhesives;

CPVC对CR/MMA体系接枝的相态结构分析
3.
On the basis of morphologies obtained by the scanning electron microscope(SEM),mechanical properties and absorption ratio test results,it has been shown that the phase structure of the blend that has undergone γ-ray irradiation is different from the un-irradiat.
扫描电镜(SEM)观察结果表明,γ射线辐照会影响共混物的相态结构;辐照4 h后,共混物样品的吸收剂量为15。
6) morphology
[英][mɔ:'fɔlədʒi] [美][mɔr'fɑlədʒɪ]

相态结构
1.
Mechanical properties, crystal and morphology properties of composites were examined.

用广角X射线衍射仪对聚丙烯的结晶状况进行了表征,计算了复合材料中聚丙烯的结晶度;用扫描电镜观察了样条的断口形貌,讨论了滑石粉填充量对材料结晶性能与相态结构的影响,以及PP相结晶度和体系的微相结构对复合材料的拉伸、弯曲及冲击性能的影响。
2.
In this paper development of polymer/clay nanocomposite in recent years based on microstructure of nanocomposites morphology,intercalation,exfoliation and crystallinty behavior etc were reviewed with 31 ref
从聚合物/粘土纳米复合材料的相态结构、影响粘土插层解离和聚合物结晶行为的因素等方面对聚合物/粘土纳米复合材料的研究近况进行了综述。
3.
The effect of IR/CR blends by adding small amount of styrenic thermoplastic elastomer(less than 10% mass)on the morphology,network and mechanical properties was studied by optical microscopy and Moony-Rivlin equation.
采用相差显微镜及Moony-Rivlin方程中的2C1和2C2等方法,研究了少量SIS,SBS,α-甲基苯乙烯和丁二烯的三嵌段共聚物(MSBMS)对IR/CR共混物相态结构、交联行为和力学性能的影响。
补充资料:结构相对指标
结构相对指标是在资料进行分组的基础上,以总体总量作为比较标准,求出各组数量占总体总量的比重,来反映总体内部的构成比重的综合指标。
说明:补充资料仅用于学习参考,请勿用于其它任何用途。
参考词条