说明:双击或选中下面任意单词,将显示该词的音标、读音、翻译等;选中中文或多个词,将显示翻译。
您的位置:首页 -> 词典 -> 弯曲滞后矩
1)  bending hysteresis moment
弯曲滞后矩
1.
The regression equation showed that wrinkle recovery angle increased linearly along with the increase of bending rigidity, but decreased with the increase of bending hysteresis moment.
通过SAS回归分析得到织物弯曲刚度、弯曲滞后矩与折皱回复角的线性回归方程。
2)  hysteresis of bending
弯曲滞后
3)  bending hysteresis
弯曲滞后量
4)  cloth bending hysteresis
织物弯曲滞后性
5)  moment versus curvature hysteretic curves
弯矩-曲率滞回曲线
1.
It investigated the failure shape,and analysed moment versus curvature hysteretic curves.
研究了试件的破坏形态,对其弯矩-曲率滞回曲线、骨架曲线进行分析,考察其滞回性能、延性、耗能能力等重要抗震性能指标。
6)  bending moment
弯曲力矩
1.
This article analyses the state and the distribution of the stress and the strain in the deformed region of steel tube,and then introduces the calculation equation of tube bending moment derived,and also how to apply it to the design of a tube bender.
分析了管材弯曲变形区的应力应变状态及其分布 ,导出了管材弯曲力矩的计算公式 ,并将之应用于弯管机设
2.
According to different deformation rates in various parts of rail head after rail straightening,stress and bending moment were analyzed in the process of rail straightening by means of the mechanics of materials and elasticity.
针对钢轨矫直后轨头各部分展宽量不一样的现象 ,运用材料力学、弹塑性力学等知识对钢轨矫直过程的应力及弯曲力矩进行了分析 ,并对实验室实物钢轨 3点弯曲模拟试验结果进行了分析 ,初步掌握了钢轨矫直过程中轨头不均匀变形和表面变形的原因。
3.
This paper analyses the cause of producing impression on the end of round steel sheared by arc knife-edge shears and puts forward the method to produce anti-bending moment by increasing the length of force arm based on lever principle for enhancing the end quality of sheared round stee
分析了弧剪刃剪切圆钢时轧件剪切端头产生压痕的原因,提出了运用杠杆原理,增加力臂长度,产生反弯曲力矩,以及提高剪切圆钢的端头质量的方法。
补充资料:弯曲工艺的概念及弯曲件

1.弯曲工艺:是根据零件形状的需要,通过模具和压力机把毛坯弯成一定角度,一定形状工件的冲压工艺方法。


2.弯曲成形工艺在工业生产中的应用:应用相当广泛,如汽车上很多履盖件,小汽车的柜架构件,摩托车上把柄,脚支架,单车上的支架构件,把柄,小的如门扣,夹子(铁夹)等。 


弯曲的基本原理:以V形板料弯曲件的弯曲变形为例进行说明。其过程为: 
   1. 凸模运动接触板料(毛坯)由于凸,凹模不同的接触点力作用而产生弯矩, 在弯矩作用下发生弹性变形,产生弯曲。
  2. 随着凸模继续下行,毛坯与凹模表面逐渐靠近接触,使弯曲半径及弯曲力臂均随之减少,毛坯与凹模接触点由凹模两肩移到凹模两斜面上。(塑变开始阶段)。
  3.随着凸模的继续下行,毛坯两端接触凸模斜面开始弯曲。(回弯曲阶段)。
   4.压平阶段,随着凸凹模间的间隙不断变小,板料在凸凹模间被压平。
  5. 校正阶段,当行程终了,对板料进行校正,使其圆角直边与凸模全部贴合而成所需的形状。 


弯曲变形的特点:  弯曲变形的特点是:板料在弯曲变形区内的曲率发生变化,即
弯 曲半径发生变化。从弯曲断面可划分为三个区:拉伸区、压缩区和中性层。

说明:补充资料仅用于学习参考,请勿用于其它任何用途。
参考词条