|
|
您的位置： 首页 -> 词典 -> 低剖面涡流发生器
1) low-profile vortex generator
低剖面涡流发生器
2) Vortex generator
涡流发生器
1.
Numerical simulation of heat transfer enhancement mechanism of small-scale vortex generator;
小尺度涡流发生器强化传热的数值模拟
2.
A source term model was applied to numerical simulation of a vane vortex generator,where the lift force created by a vane vortex generator was used as one part of the prototype of source term model,and a normal force was introduced as the other one.
将源项模型应用于叶片涡流发生器的数值模拟中,以叶片在当地流场中产生的升力作为源项一个分量原型,并引入了法向力作为源项另一个分量原型。
3.
The paper puts forward a new-type vortex generator enhancing heat exchange of solar air-drier and air-heater on the gas side and makes experiment and mechanism analyses have been presented.
提出一种强化太阳能热风干燥器和集热器气侧换热的新型涡流发生器—斜截半椭圆柱体,并对其进行了实验研究及机理分析。
3) vortex generator jet
涡流发生器
1.
The internal flow of a low-speed centrifugal compressor with and without vortex generator jet(VGJ)was simulated numerically by using CFD method.
本文采用数值计算方法对带有和不带有涡流发生器(Vortex Generator Jet,VGJ)的低速离心压气机叶轮内流动进行了数值模拟,分析了涡流发生器不同配置参数对压气机叶轮性能的影响,较为详细地揭示了叶轮内流动特性,数值计算结果证明了采用涡流发生器实现离心压气机叶轮内部流动控制的有效性。
2.
The research development of vortex generator jet in flow control is reviewed from both sides of experiment measurements and numerical calculation.
从实验测量和数值计算两个方面对涡流发生器流动控制的基础研究和应用研究进行评述,介绍了涡流发生器在流体机械流动控制中的应用及其取得的主要研究成果,最后指出了涡流发生器发展存在的问题和发展方向。
4) vortex generators
涡流发生器
1.
CFD numerical simulation investigation of vortex generators;
涡流发生器数值计算方法研究
5) heat transfer enhancement
涡流发生器
1.
By experimental studies of heat transfer enhancement and pressure loss caused by the new type vor-tex generator- bevel cut elliptical column set in the rectangular tunnel, The paper analyzes the effect on the heat transfer and pressure loss made by vortex generator s size and orientation with Re=800-38000.
通过对矩形风道内置有新型涡流发生器一斜截椭圆柱体强化传热性能和压降特性的实验研究,分析了不同雷诺数(Re=800~38000)工况下涡流发生器的几何尺寸和迎流方位对传热和压降的影响。
6) heat transfer enchancement
纵向涡流发生器
补充资料：关于solidworks 中的剖面线中的剖面线
solidworks的剖面线线型定义和autocad相同,它使用了autocad的剖面线定义方法,与autocad通用.因此,可以对剖面线进行定义. 方法:修改\SolidWorks\lang\chinese-simplified\sldwks.prn 用笔记本打开该文件,添加需要的线形.如 ;; Based on AutoCAD Ver.13.0s Hatch Pattern File ;;;; solidworks 区域剖面线定义文件 :: *金属, (Iron BrickStone), ANSI Iron, Brick, Stone masonry 45, 0,0, 0,.125 *塑料, (Lead Zinc Mg), ANSI Lead, Zinc, Magnesium, Sound/Heat/Elec Insulation 45, 0,0, 0,.125 135, 0,0, 0,.125 *玻璃,AR-GLASS@1.0 45,0,0,0,0.5, 0.5,-0.5 45,0,0.1414214, 0,0.5, 0.3,-0.7 45,0.1414214,0, 0,0.5, 0.3,-0.7 *软木, Cork material@1.0 0, 0,0, 0,.125 135, .0625,-.0625, 0,.35355339, .176776696,-.176776696 135, .09375,-.0625, 0,.35355339, .176776696,-.176776696 135, .125,-.0625, 0,.35355339, .176776696,-.176776696 *无, None 删除不需要的定义类型,可以大大提高solidworks 的启动速度
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条
|