1) typical microstructure
典型显微结构
2) embedding microstructure model
嵌入型显微结构
1.
Design and influence factor analysis of CNTs'embedding microstructure model for CNTs/Al_2O_3 composites;
CNTs/Al_2O_3复合材料嵌入型显微结构的设计及影响因素分析
3) microstructure model
显微结构模型
1.
The microstructure model and the potential barrier model were proposed in this article through analyzing the resu.
通过对实验结果的分析,同时利用XRD、SEM、EDS等手段对复合材料的物相进行分析并对材料的微观形貌进行观察和研究后,提出了该复合材料的显微结构模型和晶界势垒模型,这两种模型从微观层面上解释了加入的N i和石墨对该复合材料的室温电阻率、PTC效应及耐电压性能的影响,与实验中观察到的现象相符合。
2.
Two aspects of the simulation of microstructure model have been studied in this dissertation: 1.
对已有的RCP-LV显微结构模型进行改进和优化,使之能更好地表征实际材料的几何结构;2。
4) microstructure
[英]['maikrəu,strʌktʃə] [美]['maɪkro,strʌktʃɚ]
显微结构
1.
Microstructure analysis on used purging plugs for ladle;
用后钢包透气砖显微结构分析
2.
Effect of ZnO Additive On Performance and Microstructure of Glass-ceramics based On Composite Tailings;
ZnO添加剂对复合尾矿微晶玻璃的性能及显微结构的影响
3.
Effect of sintering temperature on the macro-characteristics and microstructure of MgB2 superconductor;
烧结温度对MgB_2超导体宏观特征和显微结构的影响
5) micro-structure
显微结构
1.
The Micro-structure Characteristics of Wheat Leafwith Middle Canopy Temperature;
冠层温度中间型小麦叶片的显微结构特征
2.
Studies on Micro-structure of Micro-endosperm Maize;
微胚乳玉米子粒显微结构研究
3.
Based on the multi-regression analysis of sinter quality data for resent three years, the influence rules of sinter chemical composition and micro-structure on sinter metallurgical properties in BAOGANG were found out.
通过对包钢近三年的烧结矿质量检测数据进行多元回归分析研究,找出了包钢生产条件下,烧结矿化学成分及其显微结构对烧结矿的冶金性能的影响规律。
6) microstructures
显微结构
1.
Properties and microstructures of polypropylene/montmorillonite nanocomposite;
聚丙烯/蒙脱石纳米复合材料的性能及显微结构
2.
The effects of microstructures of mullite and its multi - phase materials on their room temperature strength, high temperature strength,creep resistance and thermal shock resistance have been reviewed and generalized.
对莫来石及其复相材料的显微结构对其常温强度、高温强度、高温抗蠕变性、抗热震稳定性的影响进行了评述和总结,并从原料、烧成温度、添加剂及其他等方面讨论了制备工艺对优化材料显微结构及改进材料力学性能的影响。
3.
Their densities, porosities and microstructures were tested and observed.
以沥青、沥青加焦炭粉和树脂加焦炭粉 3种预浸料制备纤维预浸体 ,模压成型制备初坯体 ,然后用沥青液相法制备了 3种单向C/C复合材料试样 ,对这些试样的密度、孔隙率和显微结构进行了测试和观察。
补充资料：镁铬质耐火材料基质结构单元显微结构
镁铬质耐火材料基质结构单元显微结构
镁铬质耐火材料基质结构单元显微结构
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条