说明:双击或选中下面任意单词,将显示该词的音标、读音、翻译等;选中中文或多个词,将显示翻译。
您的位置:首页 -> 词典 -> 工艺过程中测试
1)  on-line test
工艺过程中测试
2)  processing monitoring
工艺过程监测
3)  process development wafer
工艺过程开发用测试薄片
4)  process monitoring
工艺监视,工艺监控,过程控制;工艺监测,过程监测
5)  Technological process
工艺过程
1.
The paper briefly introduces the characters of warm extrusion and emphases on application advantages for parts of aluminum alloy shells and influencing factors on technological process.
简要介绍了温挤压技术的特点,重点介绍了该技术在铝合金壳体类零件上的应用优势和影响工艺过程中的各种因素,温挤压技术已成功推广应用于铝合金壳体类零件成形的批量生产之中,使生产成本降低25%,生产效率提高70%。
2.
In view of the characteristics of technological process in chemical plants,it is suggested that the identification of hazards and dangers in this kind of plants should be achieved by combining the method of HAZOP(hazard and operability study) on the basis of direct-viewing and empirical analysis and system safety analysis.
鉴于化工企业工艺过程的特殊性,笔者建议其危险、有害因素的辨识可以在直观经验分析法和系统安全分析法的基础上,结合危险和可操作性研究(HAZOP)的思想来进行辨识。
3.
The technological process, principles and the key points of technology controlling of the thermosetting plastic by using the fusible core injection moulding were described.
阐述了用可熔型芯注射成型热固性塑料的工艺过程和原理、工艺控制要点。
6)  technical process
工艺过程
1.
Introduces frame and design parameter of the bidirectional boring machine, compares and analyzes technical process that load assembly has been manufactured at the bidirectional boring machine or no, explains the bidirectional boring machine characteristics and significance in manufacture of hydraulic support.
对双面镗床使用前后,液压支架承载结构件加工工艺过程进行分析、比较,阐述了该专用设备投入使用后的特点以及双面镗床设备在液压支架制造中的重要性。
2.
Introduces the technical process of hydraulic support cylinder bore enlarge,and give checking strength for it.
介绍了液压缸体的失效状况 ,通过对比采用扩镗方法修复缸体 ,并介绍了液压缸体扩镗的工艺过程 ,对其进行强度验算。
3.
Firstly, the article mainly introduces the working principle and characteristic of Selective Laser Sinter (SLS) technology and explains the technical process of SLS system with schematic.
介绍了选择性激光烧结(SLS)技术的工作原理及特点,用原理图直观地展示了SLS系统的工艺过程;详细阐述了其系统构成及成形过程中的优缺点;分别以直接制模法和间接制模法说明了选择性激光烧结技术(SLS)在模具制造中的应用,并且给出了它在实际应用中的例子。
补充资料:测试结果可接受性的检查和最终测试结果的确定


测试结果可接受性的检查和最终测试结果的确定
check of the acceptability of test results and determination of the final test result

  C凡(3)二3.3d,时,取此3个结果的平均值作为最终侧试结果;否则取它们的中位数作为最终测试结果。。,为重复性标准差(即在重复性条件下所得侧试结果的标准差)。 在口田T 11792一1989中还对重复性和再现性条件下所得侧试结果可接受性的检查方法和最终测试结果的确定做了详细讨论和规定。(马毅林)ceshi 11叩uo kejieshCxjxing d6 iiancha he zuizhong ceshi】i闪旧de que心ing测试结果可接受性的检查和最终测试结果的确定(checkof山eac,ptability of test,ults助ddsterminationofthefi耐testresult)在商品检验中进行一次测试的情形不多见,当得到一个测试结果时,所得结果不可能直接与给定的重复性标准差作可接受性的检查。对测试结果的准确性有任何疑问时都应再进行一次测试。所以,对两个测试结果进行可接受性的检查是一般的情况。 可接受性的检查,实际上是一种统计检验。任何两个测试结果只要能通过可接受性的统计检验即可认为是一致的,均可接受。比如,在重复性条件下,所得结果之差的绝对值(下称绝对差)不超过相应的重复性限r(见重复性和再现性)的值,则认为两个结果是一致的,均可接受;如果两个侧试结果的绝对差超过r,则认为它们是不一致的,必须增加测试。 按国家标准《测试方法的精密度在重复性或再现性条件下所得测试结果可接受性的检查和最终测试结果的确定》(GBIT 1 1792一1989),在重复性条件下,如果两个测试结果的绝对差不超过r的值,可取两个侧试结果的平均值作为最终测试结果。如果两个结果的绝对差超过r的值,并且测试费用较低,须再做两次测试。当4个结果的极差(即其中的最大值与最小值之差)不超过相应的临界极差c,瓜(4)二3.6a,时,取4个结果的平均值作为最终测试结果。如果两个结果的绝对差超过r的值,并且测试费用较高时,只须再作一次测试。当3个结果的极差不超过相应的临界极差
  
说明:补充资料仅用于学习参考,请勿用于其它任何用途。
参考词条