1) single-phase electric pump
单相电泵
2) single electron pumping
单电子泵
1.
Since single electron pumping in the novel semiconductor-based quantum dot device does not rely on Coulomb blockade of tunnelling,the de.
由于新的半导体量子点单电子泵不是依赖库仑阻塞效应通过隧穿进行单电子输运,因此,该器件就不会受到固定隧穿时间引起的低工作频率限制。
3) electronically controlled unit pump
电控单体泵
1.
The design process and method of constant velocity cam for electronically controlled unit pump were illuminated.
阐述了电控单体泵等速供油凸轮设计流程及方法,以平均供油速率为出发点,首先设计凸轮的基圆,然后进行升程段和回程段的设计;在设计过程中,使用加速度为直线方程的过渡段,使凸轮各段的加速度连续,避免了凸轮在工作中由于加速度不连续造成冲击。
2.
Based on the fuel injection system with electronically controlled unit pump and operation characteristic of vehicle and diesel engine,an idle control strategy to improve the idle performance was developed.
基于电控单体泵燃油喷射系统,根据车辆和柴油机的运行特性设计了怠速控制算法来改善怠速性能。
4) electronic unit pump
电控单体泵
1.
Pilot injection control algorithm for an electronic unit pump diesel engine;
预喷射控制算法在电控单体泵柴油机上的应用
2.
Research on Torque Based Control Simulation Model for Electronic Unit Pump Diesel Engine;
基于扭矩控制的电控单体泵柴油机仿真模型的研究
3.
Application and Investigation of Fuel Injection System of Electronic Unit Pump of 12V240ZJ Diesel;
12V240ZJ型柴油机电控单体泵燃油喷射系统的应用研究
5) electronic control unit pump
电控单体泵
1.
A squeeze damping film analysis of solenoid valve for electronic control unit pump fuel injection system;
电控单体泵电磁阀内阻尼油膜的挤压流动分析
2.
Electric and hydraulic delay characteristics of the electronic control unit pump(EUP) under different running conditions were calibrated on the EFS pump test bench and studied base on the injection pulse,pressure at pump end and the injection velocity rate signals.
在EFS油泵试验台上,结合电磁阀供油脉冲、泵端压力和喷油速率信号,研究了不同工况下电控单体泵燃油喷射系统的电液延迟特性。
6) electronic unit-pump
电控单体泵
1.
A control system of electronic unit-pump was designed based on driving circuits,transient speed of cam shaft during injection was predicted through conjoint cycle algorithm combined with parameters self-adapting.
在驱动电路的基础上设计了电控单体泵的控制系统,采用相邻循环法结合参数自适应修正对喷油时段的凸轮轴瞬时转速进行预测,完成了燃油喷射控制中凸轮轴角度和时间之间的转换。
补充资料：装箱单、重量单、尺码单
装箱单、重量单、尺码单
[装箱单、皿t单、尺码单1装箱单(Pack-ing Ust)是说明货物包装情况的单据，包括包装材料、包装方式，以及详细的包装内容，如花色、规格搭配等。进口地海关主要依据装箱单对某一特定内容的包装内容进行检查，也是进口商核对货物的依据。装箱单的内容有:单据名称、卖方名称、唆头、件数、规格、数量、毛净重、签字等。 重量单(Weight ust)是由卖方或第三者提供的，表明货物重量的单据。一般包括皮、毛、净重。它必须和其他单据上所表示的货物重量一致。 尺码单就不详细介绍了。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条