1) vibrating shaft

振动轴
2) Axial vibration

轴向振动
1.
Analysis of axial vibration fault of large generator set and its countermeasures;

大型发电机组轴向振动故障的分析及对策
2.
Study on mechanism of axial vibration of water-turbine generator units;

水力机组轴向振动机理分析研究
3.
Analysis of characteristic of axial vibration in low-speed long-stroke marine engine;

长行程船用柴油机轴系轴向振动特性的分析
3) Shaft chattering fluctuation

轴振波动
4) shaft vibration

轴振动
1.
Measurement of shaft vibration for turbo-generator units and discussion on vibration protection;
汽轮发电机组轴振动测量的分析及振动保护改进建议
2.
Since 1999,the shaft vibration of the high pressure cylinder of the air compressor was very serious.
自 1 999年起空气压缩机高压缸的轴振动就一直居高不下 ,通过对所采集的几个典型频谱图的分析 ,最终找到了原因 ,问题得到解决。
3.
The data of shaft vibration of turbo-generator is an important techno-index to safety running.
汽轮发电机的转子轴振动信号数据是监测设备安全运行的一项重要技术指标。
5) bearing vibration

轴承振动
1.
Study on technology of rolling bearing vibration、noise and abnormal noise test system;

滚动轴承振动、噪声和异音测试技术系统研究
2.
Cause analysis and treatment for excessive bearing vibration of 125 MW steam turbogenerator;
125MW汽轮发电机组轴承振动偏大原因分析与处理
3.
2 bearing vibration increase during the hot starting and the add load course, summarizes the effectual measure from actual operation experience for the reference to deal with the similiar problems.
7/537/537型汽轮机的结构特点,通过对其在热态启动加负荷过程中主机2#轴承振动大的原因进行分析,从实际运行经验中总结出行之有效的措施,为同类型机组针对类似问题的预防和处理提供了借鉴。
6) Shafting vibration

轴系振动
1.
Experimental Research about Influence of Rubber Bearing Stiffness on Shafting Vibration;

橡胶轴承材料硬度对轴系振动影响的试验研究
2.
the phenomena of impeded casing expansion and shafting vibration occurred.

山西大唐国际云冈热电机组运行中,存在汽轮机轴系振动和汽缸膨胀不畅。
3.
This paper researches on the causes and development of the shafting vibration in big turbogenerator unit, and summarizes its torsion, coupling system of bend and torsion, and control above systems, moveover, the tendency on the development of the control is also studied.
分析了大型汽轮发电机组轴系振动产生的原因及其研究的发展过程 ,对大型汽轮发电机组轴系扭转振动、弯扭耦合振动及其控制研究进行了综述 ,并对大型汽轮发电机组轴系振动及其控制研究的未来进行了展望。
补充资料:轴向缠绕
分子式:
CAS号:
性质:用热固性树脂生产长纤维增强塑料制品时纤维缠绕的一种方式。此法的缠绕方向与旋转轴平行,用热固性树脂黏结剂浸渍后的玻璃长纤维束按一定方式缠绕在芯模上,然后固化成型为一定形状的增强塑料制品。主要用于制造球状或椭圆形制品。
CAS号:
性质:用热固性树脂生产长纤维增强塑料制品时纤维缠绕的一种方式。此法的缠绕方向与旋转轴平行,用热固性树脂黏结剂浸渍后的玻璃长纤维束按一定方式缠绕在芯模上,然后固化成型为一定形状的增强塑料制品。主要用于制造球状或椭圆形制品。
说明:补充资料仅用于学习参考,请勿用于其它任何用途。
参考词条