1) uniform slab
均厚板
2) uniform thickness slab
均匀厚平板
3) average web width to thickness ratio
平均腹板宽厚比
1.
The effects of average web width to thickness ratio and web tapering ratio on post-buckling strength of H-section tapered members are analyzed.
考察了平均腹板宽厚比、楔率等参数对H型钢楔形薄壁构件屈曲后强度的影响 ,获得了一些有价值的结
4) nonhomogeneous moderately thick plate
非均质中厚板
1.
A meshless local radial point interpolation method (LRPIM) for the bending analysis of a nonhomogeneous moderately thick plate is presented in this paper.
用无网格局部径向点插值法分析了非均质中厚板的弯曲问题。
2.
A meshless local radial point interpolation method for the analysis of nonhomogeneous moderately thick plate is presented in this paper.
采用无网格局部径向点插值法来分析非均质中厚板的弯曲问题。
5) thick plate
厚板
1.
Welding technology of Cu-Ni alloy B10 thick plate;
Cu-Ni合金B10厚板焊接工艺
2.
Friction-stir welding on thick plate of 7A52 aluminum alloy;
7A52铝合金厚板搅拌摩擦焊
3.
Prediction of angular distortion in thick plate multi-pass weld;
厚板多层多道焊角变形分析方法
6) plate
[英][pleɪt] [美][plet]
厚板
1.
Construction and reform/expansion of aluminum alloy plate worldwide;
世界铝厚板系统的建设与改扩建
2.
The effects of total deformation on the microstructure and room temperature tensile properties of BT-20 alloy plate were studied in α+β.
主要研究了在α+β区总变形量对BT-20钛合金厚板组织与性能的影响,获得了在两相区总变形量控制在71%、85%和91%生产出的三种规格厚板在相同热处理制度下的显微组织以及所对应的室温力学性能。
3.
The effects of four typical structures on the mechanical properties, impact ductility and fracture toughness etc of BT-20 alloy plate were studied under the conditions of room & high temperature.
主要研究了BT-20钛合金厚板4种典型组织对室温、高温力学性能、冲击和断裂韧度等性能的影响。
补充资料：挤压制品壁厚不均匀
挤压制品壁厚不均匀
non-uniform thickness of extruded products
J iya zhiPinb一hou buiunyun挤压制品壁厚不均匀(non一uniform thick-ness of extruded Produets)供冷轧和冷拔月的挤压管料的壁厚超出允许偏差范围的一种挤压制备缺陷。挤压管料的平均壁厚偏差可按下式计算:平均璧厚偏差一名义壁厚尺寸一(最大壁厚一最小壁厚)/2。允许的最大壁厚差占可按下式计算: 。一氢袭鲁漂愿x成品管壁厚偏差 一成品管名义壁厚八二“。二，，， 壁厚不均的产生原因有:挤压筒、挤压杆、穿孔针和挤压模等的轴线不在同一直线上;锭坯壁厚不均及切斜度太大;挤压杆、穿孔针弯曲;挤压筒磨损过大，工作部分及非工作部分直径相差大;挤压筒、挤压模和挤压垫片之间的间隙过大;设备失调，螺丝不紧，上下中心扭动等。冷轧管毛料的生产已趋向于采用舌形模挤压，而不采用二次挤压，这样可有效地减小壁厚不均匀。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条