1) low resistancealloy
低电阻合金;低变形抗力合金
2) SB alloy
低温电阻合金
3) Low-alloy and rounding deformation bars
低合金盘圆变形钢筋
4) low-carbon low-alloy
低碳低合金
1.
By researching and analyzing low-carbon low-alloy steel component, technique of heat treatment, metallurgical structure and mechanical characteristic, using foreign experience for reference, this paper indicates that low-carbon low-alloy steel is one of the perfect materials under the high stress and high frequency impact condition.
通过对低碳低合金钢的成份、热处理工艺、金相组织及机械性能的研究与分析,并借鉴国外斗齿的使用经验提出低碳低合金钢是抵抗高应力、高频率冲击载荷磨粒磨损工况条件下的理想耐磨材料之一。
2.
By analyzing low-carbon low-alloy steel components, technique of heat treatment, metallurgical structure and mechanical characteristic, and using foreign experience for reference, it is found that low-carbon low-alloy steel is one of the perfect wear-resistance materials under the high stress and high-frequency impact conditions.
挖掘机斗齿由于受多种复杂工况条件及软介质的影响,传统高锰钢(ZGMn13)斗齿不能满足其磨损要求;通过对低碳低合金钢的成份、热处理工艺、金相组织及机械性能的研究与分析,并借鉴国外斗齿的使用经验指出低碳低合金钢是抵抗高应力、高频率冲击载荷磨粒磨损工况条件下的理想耐磨材料之一。
5) low-alloy steel
低合金钢
1.
Acicular ferrite microstructure of weld metal for low-alloy steel;
低合金钢焊缝的针状铁素体微观组织
2.
Study on accounting model of austenite grain size in low-alloy steel weld metal;
低合金钢焊缝金属中奥氏体晶粒尺寸计算模型的研究
3.
Prediction of PF volume fraction in low-alloy steel welding seam;
低合金钢焊缝中先共析铁素体组织数量的控制
6) low-alloy
低合金
1.
The development of hot-rolled high-strength low-alloy H-beam in Laigang was summarized.
对莱钢生产的热轧低合金高强H型钢进行了总结,论述了该类H型钢的生产工艺和化学成分优化设计思路。
2.
The jaw made of the Re low-alloy air-quenched wear-resistant cast steel was developed with the characteristics of simple process, lower cost and good mechanical properties.
新型稀土低合金空淬耐磨铸钢腭板,具有生产工艺简单、成本低、性能优良等特点。
3.
A new low-alloy wear-resistant cast steel is introduced in the paper.
一种新型低合金耐磨铸钢经空淬处理,获得下贝氏体和马氏体组织,综合机械性能优越。
补充资料：低弹变形丝
分子式：
CAS号：
性质：假捻变形丝一种，其卷曲伸长率大多为10％～35％。即将高弹变形丝经热定型处理后伸缩性下降和蓬松性提高。也可采用双区加热的假捻法，将原丝加捻、定型和解捻后，再经松弛热定型而成。以涤纶为主，具有良好的尺寸稳定性和蓬松性、稳定的卷曲、清晰外观、手感好。用于针织或机织制仿毛或仿真丝织物。
CAS号：
性质：假捻变形丝一种，其卷曲伸长率大多为10％～35％。即将高弹变形丝经热定型处理后伸缩性下降和蓬松性提高。也可采用双区加热的假捻法，将原丝加捻、定型和解捻后，再经松弛热定型而成。以涤纶为主，具有良好的尺寸稳定性和蓬松性、稳定的卷曲、清晰外观、手感好。用于针织或机织制仿毛或仿真丝织物。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条