1) gas-alternating-polymer
气聚交替
2) gas/polymer alternate injection
气聚交替注入
1.
Investigation of the technique of gas/polymer alternate injection at the middle-late stage of polymer flooding;
聚驱中后期气聚交替注入提高驱油效果试验
3) alternating copolymerization
交替共聚
1.
Study on the alternating copolymerization of vinyl acetate-Maleic anhydride using benzoyl peroxide as initiation;
马来酸酐与乙酸乙烯酯交替共聚合反应的研究
2.
The alternating copolymerization of maleic anhydride with styrene oxide catalyzed by Fe(acac) 3-Al-(i-Bu) 3 was studied.
应用Fe(acac)3 Al (i Bu)3 催化苯基环氧乙烷(SO)与马来酸酐(MA)交替共聚,共聚反应的适宜条件是: [MA] =2。
3.
The alternating copolymerization of phthalic anhydride (PA) with cyclohexene oxide (CHO) catalyzed by Fe(acac) 3 Al( i Bu) 3 α,α′ dipy (acacacetylacetone, dipydipyridine) was studied.
用Fe(acac) 3 Al(i Bu) 3 α ,α′ dipy(acac 乙酰丙酮 ,dipy 联吡啶 )催化邻苯二甲酸酐与环氧环己烷开环交替共聚反应 ,研究了Fe/Al,Fe/α,α′ dipy摩尔比对聚合反应的影响 。
4) water alternating gas
水气交替
1.
Numerical simulation of near-miscible flooding of water alternating gas considered hysteresis effect;
考虑滞后效应的水气交替近混相驱数值模拟
2.
The implement of gas injection displacement project in Suizhong 36-1 oil field was a once more natural gas reinjection project after LD10-1 and BZ34-1 oil fields in Gulf of Bohai,but in this reinjection project the aim was to increase the oil recovery factor and to explore the method of Water Alternating Gas,so as to achieve the purpose of carbon emission reduction.
绥中36-1油田气驱替项目的实施是继渤海湾旅大10-1油田/渤中34-1油田之后的又一次天然气回注项目,但本次的回注是以提高原油采收率为目的,探索水气交替驱的方法,从而也达到了减排的目的。
5) Water alternate gas
气水交替
1.
The Numerical Simulation Research of Long Core Flooding of Water Alternate Gas Displacement Experimentation for Ma 36 Reservoir;
马36长岩心气水交替驱替试验数值模拟研究
6) WAG
[英][wæɡ] [美][wæg]
气水交替
1.
DEVELOPMENT OF THE RESEARCH ON EOR MECHANISM BY WAG;
气水交替注入提高采收率机理研究进展
2.
In the period of completing this paper, the indoor experiment is carried out to study the mechanism of water flooding-polymer flooding-WAG.
论文期间开展了室内水驱-聚驱-气水交替的机理实验研究,在此基础上结合大庆油田北东块葡Ⅰ1-2油层具体情况进行分析,证实老油田在进行水驱-聚合物驱后,处于高含水后期,采用气水交替驱提高采收率是一条切实可行的途径。
补充资料：离子注入气
分子式：
CAS号：
性质：离子注入是把离子化的杂质，例如P+，B+，As+加速到高能量状态，然后注入到预定的衬底上。离子注入技术在控制Vth(阈值电压)方面应用得最为广泛。注入的杂质量可通过测量离子束电流而求得。离子注入工艺所用气体称离子注入气，有磷系、硼系和砷系气体。
CAS号：
性质：离子注入是把离子化的杂质，例如P+，B+，As+加速到高能量状态，然后注入到预定的衬底上。离子注入技术在控制Vth(阈值电压)方面应用得最为广泛。注入的杂质量可通过测量离子束电流而求得。离子注入工艺所用气体称离子注入气，有磷系、硼系和砷系气体。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条