说明:双击或选中下面任意单词,将显示该词的音标、读音、翻译等;选中中文或多个词,将显示翻译。
您的位置:首页 -> 词典 -> 单频点校正
1)  single frequency calibration
单频点校正
2)  point correct
单点校正
1.
Then introduces main contrast examination and principles on three GPS RTK correct means: single point correction, multi- points correction parameter correction and searches precision of three correction means by the exami.
首先介绍了GPSRTK技术及其工作原理,然后在点校正实验的基础上,重点介绍GPSRTK的三种常规校正方法:单点校正,多点校正和参数校正的原理与对比实验,通过实验数据探讨了三种校正方法的精度。
2.
Due to the fact that local coordinate system is usually used in practice and coordinate and elevation in WGS-84 which are directly obtained when GPS technology is used to determine position of earth’s surface point, coordinate transformation or point correct is necessary in GPS-RTK surveying.
本文对GPS RTK的三种常规校正方法(单点校正,多点校正和参数校正)的精度进行试验研究,利用实测数据对其校正精度进行对比分析,并探讨影响校正精度的主要因素,得出了有实际意义的结论。
3)  single-point calibration
单点校正法
1.
The analysis of BTEX gas standards by single-point calibration and multipoint calibration are compared.
对比了采用标准曲线法和单点校正法测定氮气中苯系物的异同,讨论了单点校正法的测定范围,并分析了单点校正法的不确定度评定过程,说明了其不确定度的主要来源以及其中存在的问题。
4)  single-calibration-ratio iteration calculating
单点校正因子迭代法
1.
In this paper,the single-calibration-ratio iteration calculating method is proposed to improve quantitative analysis method for determination of water in water-reducible paint by Gas Chromatography(GC)and some procedures in experiment are modified.
本文提出单点校正因子迭代法,改进了气相色谱测定涂料中水的定量分析方法,并对部分实验操作步骤进行了改进。
5)  dispersion correction
频散校正
6)  spectrum correction
频谱校正
1.
Application of spectrum correction theory in phase measurement for rotate machinery;
频谱校正理论及其在旋转机械相位测量中的应用
2.
Study on the Application of Spectrum Correction in the Run-up and Shutdown Analysis for Rotary Machinery;
频谱校正在旋转机械启停分析中的应用研究
3.
Study of Harmonic Spectrum Correction Precision in Electric Power Network;
电网谐波频谱校正精度研究
补充资料:闭式单点、双点压力机
代码:00413
设备名称:闭式单点、双点压力机
型号规格:公称力≥800kN
计量单位:台
主要参数内容
国际先进国内先进国内一般国内落后评定方法及说明
(一)加工精度
    参照GB10924-89、GB10933-89、JB5200-91
1、滑块下平面对工作台上平面的平行度(mm)
30%精度储备20%精度储备达到规定值大于规定值 
0.02+0.10/100×滑块下平面的被测长度
     
2、滑块行程对工作台上平面的垂直度
30%精度储备20%精度储备达到规定值大于规定值 
0.05+0.02/100×滑块行程长度
     
(二)结构性能
     
1、离合器、制动器接通率,当滑块行程次数≤16次/分时为70%,≤25次/分时为60%,≤45次/分时为50%
大于规定值10%大于规定值达到规定值达不到规定值 
2、液压超负荷保险装置、微调装置、吨位指示器
全部具有全部具有部分具有没有 
(三)噪声dB(A)
     
1、公称力≤400kN
≤85≤87≤88>88 
2、公称力>400kN
≤87≤88≤90>90 
说明:补充资料仅用于学习参考,请勿用于其它任何用途。
参考词条