1.
The Optimal Approximation of Matrices on Some Closed Convex Cone;
矩阵在闭凸锥上的最佳逼近(英文)
2.
In this paper, we have estabished the closed convexities and connectedness of the cone weak subdiffrerential of limit mapping of set-valued mapping sequence.
在文[,4]基础上,给出了集值映射序列的极限映射的锥弱次微分的闭凸性和连通性。
3.
The single pyramid projects well into the renal pelvis.
单个锥体明显凸入肾盂。
4.
cam shaft reversing lock
凸轮轴换向闭锁装置
5.
Research on Grinding the Convexity of Taper Roller Conical Surface Lines via Centerless Grinder
无心磨床磨削圆锥滚子圆锥面素线凸度的研究
6.
Non-equalization Machining Method for Conical Cam with Oscillating Tapered Roller Follower
圆锥滚子摆动从动件圆锥凸轮的非等径加工
7.
Henig Proper Efficiency in the ic-Conen-Convexlike Set-valued Optimization Problems
生成锥内部凸-锥-类凸集值优化问题的Henig真有效性
8.
ON HENIG EFFICIENCY IN SET-VALUED OPTIMIZATION WITH IC-CONE-CONVEXLIKENESS;
内部锥类凸集值优化的Henig有效性
9.
Pareto Minimization Problem with Cone-Preinvex Mappings
锥预不变凸映射的Pareto极小问题
10.
Taper support Rib : Rib conical taper at the circumferential rib support, in between the cam groove, Roller Cam with the circumference of linear contact.
锥度支撑肋：锥形肋位于锥度支撑肋的圆周上，在凸轮凹槽之间，与凸轮滚子的圆周线性接触。
11.
The analytic method of pressure angle of the conical cam mechanism with oscillating conical roller follower
圆锥滚子摆动从动件圆锥凸轮机构压力角的解析方法
12.
The Profile Determination of Conical Cam with a Translating Follower Based on the Theory of Envelopes
应用包络面理论建立直动从动件圆锥凸轮机构凸轮廓面方程
13.
In this paper we prove that if the polar cone Λ* of a closed convex cone Λis sharp or is generated by a closed ball not containing θ, then Λ is solid.
本文证明：当锥Λ的极锥是尖锥或由不含θ点的闭球体张成时，Λ是体锥；
14.
Working Profile Curved Surface Design of Worm Cam Mechanism with Cone Roller
圆锥滚子蜗杆凸轮机构的工作轮廓设计
15.
The Ic-Cone-Convexlikeness and Its Applications in Vector Optimization Problems with Set-Valued Maps;
ic-锥—类凸性及其在集值向量优化问题中的应用
16.
Nonlinear Rescaling Methods for Nonconvex Second-Order Cone Programming Problems
非凸二阶锥规划问题的非线性重新尺度化方法
17.
Improving discussion of inspecting method for tapered roller bearing inner ring camber
圆锥滚子轴承内圈凸度检测方法的改进探讨
18.
Design and improvement of injection mould about back taper raised dome
关于带有倒锥凸起圆盖注射模的设计与改进