1.
Effect of Formation of Granular Pearlite on Wear Resistance of Troostite Classifier Blade
粒状珠光体形成对屈氏体分级机叶片耐磨性的影响
2.
Fracture Failure Analysis on Primary Impeller Blades of Vertical Air Compressor
立空压机一级叶轮叶片断裂失效分析
3.
Cause Analysis of Two-grades Axial-flow Primary Fan Blades Drifting
双级轴流一次风机叶片漂移原因分析
4.
Analysis of Manufacturing Technologies of 600MW Steam Turbine Governing-stage Moving Blade Root
600MW汽轮机调节级动叶片叶根加工工艺分析
5.
Micro Crack Analysis of Compressor Blade of Grade Ⅰ in Engine WP-7
WP—7发动机Ⅰ级压缩机叶片微裂纹分析
6.
Research on Composition, Structure and Property of the High Alloy White Cast Iron Blade Used in Classifier;
分级机用高铬铸铁叶片组织与性能的研究
7.
Analysis on Multi-order Static Frequency of Last Stage Long Blade of 1000MW Ultra Supercritical Turbines
1000MW超超临界汽轮机末级长叶片多阶静频分析
8.
Analysis of Anti-corrosion Technology for Last Rotor Blades of Large Capacity Turbines
大容量汽轮机末级动叶片防水蚀工艺分析
9.
CAUSE ANALYSIS OF FRACTURES ON LOW-PRESSURE LAST-STAGE BLADES IN N135-13.24/535/535 UNITS
N135-13.24/535/535型机组低压末级叶片裂纹原因分析
10.
Analysis of Water Erode Theory and Research on Replacement of Stellite Strip on Turbine Last Stage Blade;
汽轮机低压缸末级叶片水蚀机理分析及司太立合金片更换研究
11.
The Analysis of Vibration and Fracture of the Stage 4 Compressor Blade in a Typical Aeroengine
某型发动机第4级压气机叶片振动特性及断裂机理分析
12.
Analysis on Manufacturing Technologies of M701F Heavy-duty Gas Turbine Compressor 13 Stage Moving Blade Tip
M701F重型燃气轮机压气机第13级动叶片的加工工艺分析
13.
An Analysis of the Vibration Characteristics and Service Life of Shrouded Blades for the Wetness Removal Stage of a Marine Steam Turbine;
船用汽轮机除湿级带冠叶片振动特性及寿命分析
14.
Non-Linear Dynamic Characteristics Analysis of Megawatt Horizontal Axis Wind Turbine Blade
兆瓦级水平轴风力发电机叶片的非线性动态特性分析
15.
Breaking Cause Analysis of Shroud Band on Last Stage Blade of Low Voltage Rotor of 125 MW Set and Reconstruction
125 MW机组低压转子末级叶片围带断裂分析及改造
16.
Analysis of Low Cycle Fatigue Life for Second-stage Turbine Blade of an Aeroengine
某型发动机第2级涡轮叶片低循环疲劳寿命分析
17.
Tie-pieces Retrofit of MP Rotator's Last Stage Blade for 200 MW Generating Unit
200MW机组中压转子末级叶片拉筋改造
18.
Optimization design of typical blade profile of long blade in ultra-supercritical steam turbine
超临界机组末级叶片典型截面的叶型设计