1.
The Numerical Simulation of Weldind Defect and Welding Residual Stresses in the Spherical Tank;
球罐焊缝缺陷与焊接残余应力的数值模拟
2.
Investigation on the Formatting Mechanism and Preventing Method of the Weld Surface Defects of 9% Nickel Steel Sphere;
9%Ni钢乙烯球罐焊缝表面缺陷形成机理及解决对策的研究
3.
New Technology of Tank Welding to Bulk Powder Goods Tanker
粉粒物料运输车罐体焊缝布置新工艺
4.
The necessarily of post-weld heat treatment of spherical tanks was emphasized.
强调了焊接球罐焊后热处理的必要性。
5.
Inspecting the Storage Tank's Bottom Plate Fillet Welds by PT
渗透检测在大型储罐底板角焊缝检测中的应用
6.
Research on flexible rail type spherical tank welding robot
用于球罐焊接的柔性导轨焊接机器人研究
7.
Research of automatic tracing on tr ack type sphere welding machine
轨道式球罐焊机自动跟踪方法的研究
8.
Welding Technique of 610U2L steel Used for Ethylene Spherical Tank
610U2L钢制乙烯球罐的焊接技术措施
9.
Analysis and Patching for Cracks which Appeared after the 2000m~3 Spherical Tank Assembling Weld
2000m~3球罐组焊裂纹分析与修补
10.
Study on Cold Cracks Sensibility of Spherical Tanks by Re-welding
在役球罐再次组焊冷裂纹敏感性研究
11.
Welding Procedure for 2000 m~3 Liquid Ammonia Steel Spherical Tank Using 15MnNiNbDR Steel
-50℃用15MnNiNbDR钢制2000m~3液氨球罐焊接工艺
12.
Welding of JFE-HITEN610U2L Steel Ethylene Spherical Tank
JFE-HITEN610U2L钢制乙烯球罐的组焊
13.
Welding of JFE-HITEN610U2L Steel Used for Ethylene Spherical Tank
乙烯球罐用钢JFE-HITEN610U2L的焊接
14.
TOFD Automatic Ultrasonic Inspection on Site Butt Weld of the Four Exports Separator
四段出口分离罐现场组焊对接焊缝TOFD自动超声检测
15.
YS Automatic Girth Welder (YS-AGW-I/II) is mainly used in horizontal girth inside / outside welding of large tanks、vessel etc. The welder applies submerged arc welding.
型埋弧自动横焊机采用埋弧横向焊接工艺，主要用于大型储罐、容器等内外环缝的焊接.
16.
The Numerical Simulation on Welding Residual Stresses of the Ethylene Spherical Tank Steel;
07MnNiMoV乙烯球罐用钢焊接残余应力的数值模拟
17.
Infinite Element Stress Analysis of Welding Angle Influenced Area on 400 m~3 Spherical Vessel during Disassemble-remove-reassemble Project
400m~3球罐分拆搬迁组焊棱角区有限元应力分析
18.
Welding the welds which are stagger first, then is the straight ang long weld.
先焊错开的端焊缝，后焊直通长焊缝。