1.
Theoretical Analysis on Polymer Melt Extrusion Swell at Conical Die with Different Entrance Angles
不同角度圆锥口模对聚合物熔体挤出胀大的影响
2.
Phenomenological Studies on Extrusion Swell of Polymer Melt Through Conical Short Dies;
聚合物熔体在圆锥短口模的挤出胀大唯象研究
3.
The uniaxial elongational property and the extrusion swell through a long die for the IUPAC-LDPE melt
IUPAC-LDPE熔体的单轴拉伸特性和长口模挤出胀大
4.
Extruded swell behavior of polypropylene specialized for manufacture of meltblown nonwoven fabric
熔喷非织造布用聚丙烯材料的挤出胀大行为
5.
Experiment Study on Extrusion Swell of PS/SCCO_2 Foaming System;
聚苯乙烯/超临界CO_2发泡体系挤出胀大实验研究
6.
THE FLOW ANALYSIS OF POLYMER MELT IN CO-EXTRUSION DIE
共挤出机头中的聚合物熔体流动分析
7.
Study on Tandem Extrusion System of Single Screw-Melt Pump;
单螺杆—熔体泵串联挤出系统的研究
8.
Influence of type of extruders on melt properties of PP
挤出机类型对聚丙烯熔体性能的影响
9.
The Relationship Between Extrudate Swell Ratio and the Length of Slip Part in Gas-Assisted Extrusion
气辅挤出胀大比与滑移段长度的关系
10.
Melt spinning involves melting the nylon in an inert atmosphere, controlling the extrusion and solidification of the melt, and collecting the extruded filaments.
熔纺包括尼龙在惰性气体中的熔化、控制熔融体挤出和固化、卷绕挤出的长丝等几个过程。
11.
Slip Length of Gas-Assisted Extrusion Die Influence on Die Swell Ratio
气辅挤出口模中滑移段长度对挤出胀大比的影响研究
12.
The Flux Analysis of the Plastic Melt in Extrusion Die Circle and Construct Design Channel;
塑料熔体的流量分析与圆环型材挤出模的设计
13.
High-melt-viscosity polypropylene prepared by PP/EPDM reactive extrusion blending method
PP/EPDM反应挤出共混制备高熔体黏度PP的研究
14.
Experimental Research and Forecasted System Development of Die Swell Ratio of Polymer;
聚合物挤出胀大的实验研究及预测系统开发
15.
THE NFLUENCNG FACTORS RESEARCH OF DE SWELL RATO OF HDPE/OMMT NANO COMPOSTE
HDPE/OMMT纳米复合材料挤出胀大比的影响因素研究
16.
Research on the High-Melt-Strength Polypropylene for Foaming Prepared by Reactive Extrusion;
反应挤出法制备发泡用高熔体强度聚丙烯的研究
17.
Study on Properties of Mixing Elements in Melt Conveying Zone of Intermeshing Counter-Rotating Twin Screw Extruder;
啮合异向双螺杆挤出机熔体输送段混合元件性能的研究
18.
Study on Melt Mixing of Nano Powder and Polymer in Co-Rotating Twin Screw Extruder;
纳米粉体与聚合物在同向双螺杆挤出机中的熔融混合研究