1.
anticlinal bulge
背斜脊的厚度和高程
2.
much-faulted anticline
断裂程度很大的背斜
3.
A sharp ridge with steeply sloping sides, produced by erosion of the broken edges of highly tilted strata.
豚脊丘，陡峻的山脊由于对高斜层破碎山背的侵蚀而形成的陡峭的山背
4.
By employing gelatin half-embedding method, spinal cord slices 250-300 um thick with attached dorsal root were obtained and used to makepatch-clamp recording.
采用明胶半包埋方法制作带背根的脊髓薄片，获得厚度为250一300
5.
Spine-bulk: The thickness of the spine of a book block not including the thickness of the cover boards.
脊厚:书芯厚度,它不包括书皮纸板的厚度。
6.
FEATURES OF BAROTROPIC/BAROCLINIC VORTICITY AND ENSTROPHY DURING OKHOTSK BLOCKING DEVELOPMENT
鄂霍茨克海阻高发展过程的正斜压涡度和涡度拟能的演变特征
7.
Fast-back binding: Binding in which the spines of the sections are stuck to the back of the book,reinforcing its strength.The back can either be hard or flexible.Also known as Fixed back,Tight-back binding.
密背装:把各贴的脊部粘牢于书背上以增加强度。密背分别有硬背和软背。
8.
(2) The raised part of the book spine which is formed in the rounding and backing process. The height of the shoulder should approximate to the thickness of the board to be used for the case.
（2）书脊在圆脊及起膊时所造成的升起部份；它的高度约等于用来造书壳的纸板的厚度。
9.
Back planning: Finishing operation to the back of a stereotype or an electrotype after backing up to make it smooth and to the required height.
平背:铅铸版或电铸版在背后所需的刨平和达致标准厚度的工作。
10.
Reasonable Mining Height of Full-mechanized Caving Mining in Softly Inclined and Extra-thick Coal Seam
缓倾斜特厚煤层综放开采合理开采厚度的确定
11.
smooth dogfish of Pacific and Indian oceans and Red Sea having white-tipped dorsal and caudal fins.
太平洋、印度洋和红海水域的平滑狗鲨，长着白尖的脊背和尾鳍。
12.
a thick twilled fabric of wool and cotton.
由羊毛和棉花织成的斜纹的厚纤维。
13.
DISCUSSION ON PROBLEMS OF DEFORMATION GEOMETRY OF HIGH ANGLE UNDERTHRUST IN TIANFU ANTICLINAL STRUCTURE
天府背斜上高角度仰冲断层的变形几何学问题讨论
14.
thick-layer apt to oxidation type characterized by large thickness of coal seam and low metamorphic degree, and transition type.
以煤层厚度大和低变质程度为特征的厚层氧化类型; 过渡类型.
15.
Role of Src kinase in the induction and maintenance of spinal long-term potentiation
Src激酶在脊髓背角长时程增强的诱导和维持中的作用
16.
Shear force is interrelating with width and thickness of plate and obliquity of knife-edge.
斜刃剪切时，剪切力的大小与板料的宽度、厚度及斜刃倾角有关。
17.
Abstract: Shear force is interrelating with width and thickness of plate and obliquity of knife-edge.
文摘:斜刃剪切时，剪切力的大小与板料的宽度、厚度及斜刃倾角有关。
18.
Spacings between anticlinal crests and synclinal troughs in the member tend to be equal in some series of folds.
岩层中的背斜峰和向斜谷之间的距离趋于相等。