1.
Test of Large Hole Distance and Small Resistant Line Blasting Technique in Underground Stope
大孔距小抵抗线爆破技术在地下中深孔采场中的试验
2.
short focal length (high aperture) lens
短焦距(大孔径)透镜
3.
overall f - number
总光圈大小, 总孔径焦距比
4.
Stress Distribution Analysis for a Small Space in between the Large Nozzles Structure of Internally Pressured Cylindrical Vessel
圆形筒体小间距大开孔结构的应力分布
5.
The practice and application of kilometer-orientated large diameter and long-distance drilling
千米定向大直径长距离钻孔的实践与应用
6.
An Energy Consumed Collision-Prevention System of Long Distance Anchor Moving for Non-Navigational Bridge
非通航孔桥的大距离走锚消能式防撞系统
7.
In an ideal situation, the largest aperture in the thinnest stencil with the maximum space between apertures provides the optimum process.
实际情况，最薄的钢网，最大的孔，最大的空间距，提供最优的工艺。
8.
ratio of the pole spacing to the bore diameter of the pole pieces
极靴的间距与孔径比
9.
The bullet., at that distance, would make a small hole where it entered, but it would rip out of his back a place as big as a soccer ball.
子弹，处在那种距离，射进去会穿一个小孔，但会在他的后背撕开一个足球那样大的窟窿。
10.
Relationship between Interpupillary & Innercanthal Distance and Maxillary Anterior Teeth of People with Normal Occlusion
正常者瞳孔间距、内眦间距与上颌前牙的关系
11.
The new measuring method for distance of the gas drainage hole and seam permeability
瓦斯抽采孔孔距及煤层透气性的测定方法
12.
Study of Numerical Simulation of Fan-pattern Hole Bottom Distance of Xiaodonggou Molybdenum Mine
小东沟钼矿扇形炮孔孔底距数值模拟研究
13.
Study on Rational Borehole Space of Crossed Boreholes for Gas Pre-drainage
预抽煤层瓦斯交叉钻孔合理孔间距的研究
14.
Out of Confucius' Residence, I looked back at' the couplet pasted on each side of the gate.
孔子孔子，大哉孔子! ”出得孔府，回首看府门。
15.
Supporting the use of impact drilling electric drill. Drilling, hole spacing with hole depth should meet the design requirements.
（1）钻孔使用配套冲击电钻.钻孔时,孔洞间距与孔洞深度应满足设计要求.
16.
The average length from the zygo-alveolar ridge to the pterygomaxillary junction was 26 mm, the average length from anterior nasal spine to the posterior nasal spine was 47 mm, and the angle between the piriform rim to the descending palatine canal and vertical section was 7 8'.
犁状孔边缘至翼腭管的距离平均为37mm; 前后鼻棘的距离为47mm;
17.
The plate has holes of approximately 2 in. in diameter on 7-to 8-in. centers in staggered rows.
板上有直径近2英寸的孔眼，交错横排，孔眼中心距为7-8英寸。
18.
Influence of angles and hole pitches on discharge coefficients of expanded holes at inlet and outlet
角度和孔间距对双向扩张型孔流量系数影响的实验