1.
When the new valve is started, before the installation, should remove quakeproof matters between the discs, otherwise the respiration will malfunction.
新阀启用时，安装前应清除阀盘间防震物，否则呼吸阀将失灵。
2.
A canister purge valve is opened periodically to vent the vapor back into induction system.
收集器的清除阀周期性地开启，泄放蒸气使之返回进气系统。
3.
Pulse valve: The quality and performance of pulse valve determine the dust-cleaning effect of the pulse-cleaning filters.
一、冲阀：电磁脉冲阀的性能和质量，决定脉冲除尘器的清灰效果。
4.
Maintain the trap regularly. Clean up the dirt in the front of the gauze filter to guarntee the normal operation of the trap.
○要定期保养，清除过滤网前的污物，保证疏水阀正常工作。
5.
Clean all carbon deposits from the combustion chambers, valve ports, valve stems, valve stem guides and hea
从燃烧室、阀口、阀杆、阀导管和盖清洁所有的积碳。
6.
Flush the lines to remove all loose scale, dirt and other foreign matter that can damage or clog the valve.
冲洗管线，清除可能损坏或堵塞阀门的所有疏松的氧化皮、污垢和其它外来物质。
7.
Open the water heater drain valve and allow all the water to drain from the tank. Flush the tank with water as needed to remove sediment.
打开热水器排污阀，排泄内胆内的所有水。如果需要，用水冲洗内胆，清除沉淀物。
8.
The ACV 513-6 pump control valve starts in an open position during pump start-up, purging the deep well of air and debris to atmosphere.
6泵控制阀在泵启动期间开始处于开启的状态，将深井中的气体和碎片清除到大气中。
9.
transaction cleanup, replication cleanup, history cleanup, subscription cleanup
事务清除，复制清除，历史记录清除，订阅清除
10.
The relief valve seat is located inside of the body and can be removed, if necessary, for cleaning/inspection.
安全阀阀座位于阀体内部，如果必要，可以拆卸用于清洗/检查。
11.
To clean; remove bottom plug, seat spring, strainer and seat disc.
因此要清洗，拆卸底部塞、阀座弹簧、过滤器和阀座阀瓣。
12.
To remove(instructions or data) from a memory.
清除，清零从内存中把（指令或数据）清除
13.
Slowly pull the assembly outward to open check allowing exposure of the seat and clapper contact area for cleaning.
慢慢将止回阀往外拉，打开止回阀，使得阀座和阀瓣接触面暴露出来便于清洗。
14.
formaldehyde-scavenging agent
[游离]甲醛清除剂
15.
To get rid of(people considered undesirable).
清除（不喜欢的人）
16.
The garbage men came to clear away the rubBish.
清道夫来清除垃圾。
17.
(Except at closed throttle at speeds above 70–83 MPH)
（除了在速度大于０–８３ＭＰＨ时的节流阀处）
18.
Seat ring is seal welded to eliminate leak path.
阀座环通过密封焊接，消除泄漏通道。