1.
The upperend rests against a flat washer.
上端紧靠固定垫上。
2.
Theuse of permanent backing bars in highly stressed welds in hullstructures is to be avoided as far as possible.
例2:船体结构中，凡承受高应力的焊缝，应尽量避免采用固定垫板连接。
3.
Seat Cushion Cover Retaining Clip Removal
座椅垫盖固定螺钉拆卸
4.
Remove the three screws that secure the seat cushion side shield to the outboard seat cushion frame.
拆下固定座位垫侧罩于外缘座位垫框架上的三个螺丝。
5.
Remove the two screws that secure each outlet to the instrument panel side of the top pa
拆下固定每个出口至顶垫仪表板侧的两个螺丝。
6.
Install differential case and dummy bearings in axle housing (without shims) and tighten retaining cap bolts.
在轴壳内（没有垫片）安装差速箱和模型轴承，并紧固固定帽螺栓。
7.
The milling cutter is mounted on an arbor, where it is held in place by spacers or bushings.
铣刀装在心轴（刀杆）上，并用垫圈或轴套把它固定好。
8.
Remove the three screws that secure the seat side shield to the seat cushion frame.
拆卸固定座椅侧面防护至座椅垫支架的三个螺丝。
9.
When in place, the gasket will be seated and flush with the valve body ends.
放置好后，垫圈将与阀体连接端口一起固定和冲洗。
10.
The basket held a heart-shaped pillow to which Brad had secured our rings with pieces of wire.
篮子里有个鸡心状的垫枕，上面用金属线固定住戒指。
11.
Most of the best helmets have three elements: a shell, a liner and straps and buckle.
不专业不知道是不是这麽翻译),海绵衬垫,以及固定在头部的带子.
12.
The sponge in the cushion and the backrest are both manufactured by employing freeze foaming and forming techniques.
坐垫和背垫海绵均采用冷固化成型技术制造。
13.
The Research of Segmentation of Mattress Market and Reposition of Symbol Mattress
床垫市场细分研究及穗宝床垫重定位
14.
Continue rolling the cover downward and engage the hogrings attaching the seatback cover to the seatback cushion support wires.
继续向下旋转座椅背盖，接上固定座椅背盖到座椅背垫支架线的拱起环。
15.
and the other two rubber cushion seats 3 on the hinge side B are fixed by using a rubber-based adhesive. Then, oil pan 4 is placed.
再用螺钉2把铰链侧B的2个头部胶垫座3钉好固定，然后把底槽4放上去。
16.
Using a short piece of pipe and Holder 6958 to hold the pinion yoke, or pinion flange, remove the pinion nut and washer.
用短管和托架6958固定小齿轮轴轭或小齿轮凸缘，拆下小齿轮螺帽和垫圈。
17.
To reverse the seat disc, unscrew the disc screw and disassemble the disc washer and disc rubber from the disc holder assembly.
为了翻转阀座阀瓣，则要拧松阀瓣螺丝，从阀瓣固定器总成拆解阀瓣垫圈和阀瓣橡胶。
18.
bottom supporting drilling platform
定柱沉垫式钻井平台