1.
Reason for Low Tight Axle Strength of 10.9S Sets of Torshear Type High Strength Bolt for Steel Structures
钢结构用10.9S扭剪型高强螺栓连接副紧固轴力偏低原因分析
2.
Experimental Study on Fastening Bolt Axial Force of WSGG Anchor Basted on CFRP Sheet
CFRP波形齿锚具紧固螺栓轴力的试验
3.
Lock rings at the end of shaft with scre
GB/T891-1986螺钉紧固轴端挡圈
4.
Lock rings at the end of shaft with bolt
GB/T892-1986螺栓紧固轴端挡圈
5.
A spindle or an axle used to secure or support material being machined or milled.
紧轴一根用于固定或支撑待切削或粉碎原料的新心轴或轮轴
6.
Install differential case and dummy bearings in axle housing (without shims) and tighten retaining cap bolts.
在轴壳内（没有垫片）安装差速箱和模型轴承，并紧固固定帽螺栓。
7.
Before using they have to be preloaded.
推力球轴承在工作中必须加以轴向予紧。
8.
Axial load fatigue testing for threaded fasteners
GB/T13682-1992螺纹紧固件轴向载荷疲劳试验方法
9.
One of the pegs securing the strings and regulating their tension on a stringed instrument.
弦轴，琴轸用来固定弦或调弦的松紧的部分
10.
Testing Method Research of Preloading on the Ball Bearing Used in Gyro Motor
陀螺仪马达轴承预紧力测试方法研究
11.
Bring the walking foot as close to presser foot 3 as possible to the extent that it does not come in contact with the rear face of presser foot. Securely tighten screw 2 in the center shaft bell crank.
移动外压脚，一直移动到不能顶到中压脚3的背面的位置，紧紧地拧紧中轴轮紧固螺丝
12.
A new structure for fixing the bearing bush of the connecting lever in a crankshaft press is introduced.
针对曲轴压力机连杆上轴瓦的固定问题，介绍了一种新的固定结构。
13.
The Improvement of Connecting Pin-lubrication in Tension Roller Compactor Frame
张力压紧辊架连接销轴润滑方式的改进
14.
Install the pinion mate shaft lock screw finger tight to hold shaft during differential installation.
在差速器安装期间，安装小齿轮配合轴锁螺丝，用手紧固它，以把握住轴。
15.
Axis positioning buildings, infrastructure and elevation axes, anchor bolt fastening should conform to the specifications and design requirements.
建筑物的定位轴线、础轴线和标高、脚螺栓的规格及其紧固应符合设计要求。
16.
The types and working principle of preload of the angular contact ball bearings are introduced, the selection rules of the preload and calculation method of determining preload force are given.
介绍角接触球轴承预紧的类型及工作原理,给出了预紧选择原则和确定预紧力的计算方法。
17.
The clutch rotor is fixed on the input shaft and the clutch armature is fixed on the output shaft.
离合器的转子固定在入力轴，而离合器的电极板与刹车被固定在出力轴上。
18.
The Experimental Research on the Influence of Different Convergence Angles on the Retention of Metal Full Crowns;
轴壁聚合度对金属全冠固位力影响的实验研究