1.
The effect of initial hydrogen temperature on LOX/GH_2 liquid rocket engine combustion instability
氢喷射温度对氢氧火箭发动机燃烧稳定性的影响
2.
At any given element spacing, the minimum stable operating hydrogen injection temperature varied linearly with face coverage.
对于任何给定的单元间距，稳定工作的最低氢喷射温度随喷注面覆盖而线性地变化。
3.
Simulation of the blowout jet fire temperature field and radiation field based on CFD
基于CFD的井喷失控喷射火温度场和辐射场模拟仿真
4.
The Research of Temperature Field Analysis and Application on Laser Remelted Coating Oriented by Jet Electroforming;
喷射电镀层激光重熔的温度场分析及应用研究
5.
Comparison of Diesel and DME Injection System Performances at Different Temperatures
温度对柴油和二甲醚喷射系统性能的影响
6.
Mathematical Simulation on Solidification Process and Temperature Field of Deposition Billet during Spray Forming
喷射成形沉积坯凝固过程和温度场的数值模拟
7.
The speedy cooled strip is equalized here to the temperature accepted by zinc pot.
使经快速喷射冷却的钢板温度均匀一致,达到钢板入锌锅的温度。
8.
Sprinkling creates water particles in the air that reduce outgoing radiation, but plant temperature declines immediately on cessation of the operation.
喷洒在空气中产生小水滴，它们使射出辐射减小，但是喷洒一停止，植物本身温度立刻下降。
9.
The strip is cooled from heat treatment temperature to around 480 c with high efficiency spray cooling device quickly.
利用高效喷射冷却装置快速地将带钢从热处理温度冷却至480℃左右。
10.
When the surface temperature during laser illumination reached 36-45℃, a 30-100 m/sec cryogen spurt was delivered.
利用红外线温度检测回馈系统来控制冷媒喷射出的时间。
11.
The infrared radiation and wall temperature were obviously decreased by cooling.
通过冷却，各喷管的壁温和红外辐射强度明显降低。
12.
Research on Temperature Field Numerical Simulation and Performance of Laser Re-melted Ni-coating Oriented by Jet Electroforming on 45 Steel;
45钢喷射电镀镍层激光重熔温度场数值模拟及其性能研究
13.
THE EFFECT OF ANNEALING TEMPERATURE AND TIME ON GRAIN GROWTH OF SPRAY-DEPOSITED A356 ALLOY IN SEMISOLID METAL PROCESSING
半固态加热温度和时间对喷射沉积A356材晶粒长大的影响
14.
Coupling analysis of temperature and stress fields of shotcrete slope in soft rock area
软岩地区喷射混凝土边坡变形分析——温度场与应力场的耦合效应
15.
In agreement with this concept is the additional experimental result that decreasing the mean hydrogen injection velocity increases the stability limit temperature.
这一概念是与补充试验的结果相符的，即降低氢的平均喷射速度使稳定性极限温度增加。
16.
fully-flooded high temperature jet-dyeing machine
全浸没式高温喷射染色机
17.
mean radiant temperature
平均辐射温度 平均辐射温度
18.
Occasionally, when temperatures exceeding the boiling point of water are used for pasteurization, the final stage of heating is accomplished using direct steam injection.
偶尔,当巴氏杀菌的温度超过水的沸点时,最后的加热段使用直接喷射蒸汽来完成。