1.
Self-closing connect valve can be installed at apron, high and low point draining outlet of depot pipeling.
自闭式接头阀可安装在机坪、库管线的高低点排放出口。
2.
Assessing the safety of fully welded body pipeline ball valve
全焊接阀体管线球阀焊接接头的安全评估
3.
Grooved butterfly valves direct connect to pipe using iron pipe size couplings. Grooved valves are easiest to install.
管状蝶阀:采用铸铁管接头直接与管道连接。管状阀门安装最容易。
4.
A DISS connection is a gasketed type that consists of the valve outlet, nut, nipple, and gasket.
DISS接头是一种衬垫型接头，由阀门排气口、母、接口和衬垫组成。
5.
Kit includes: Primary& Secondary checks, seat and two union seals.
组件包括：第一和第二止回阀，阀座和两个管接头密封。
6.
"Valve Stand: Support air supply header and various takeover points, flex hoses, gauges, valves, etc."
阀架上面安架空气接头,各种转换点,软管,计量表,阀门等。
7.
The union bonnet offers strength and ease of assembly-disassembly.
管接头式阀盖具有一定的强度,易于安装和拆卸。
8.
Reattach the relief valve hose to the elbow in the bottom flange cover.
重新将安全阀软管接到底部法兰盖内的弯头上。
9.
Improve Designing of the Quick-connect Seal for the Regulating Valve
一种调节阀快速接头新型密封件的改进设计
10.
The assembly shall also include two resilient seated isolation valves, four top-mounted resilient seated test cocks and an air gap drain fitting.
这种总成应该包括两个弹性阀座隔离阀，四个顶部安装弹性阀座测试旋塞和一个气隙排放接头。
11.
The heat source must not directly heat the container valve since the valve, connection, and relief device components can be damaged by excessive temperatures.
由于过高的温度会损坏阀门、接头和减压装置组件，热源不能直接加热容器阀门。
12.
hose connection valve
软管联结阀软管连接阀
13.
Leaks occurring at the cylinder valve's pressure relief device, diaphragms, or valve to the cylinder connection cannot be repaired.
发生在钢瓶阀门的减压装置、横膈膜或阀门到钢瓶的接头处的泄露不能维修。
14.
Install a shutoff valve in the cold water inlet. Install a listed temperature-pressure relief valve in the remaining fitting.
在冷水进水管上安装一个关断阀。在剩下的螺纹接头上安装额定温度/水压的安全阀。
15.
11 Adapters to convert cylinder valves from one type of gas to another can lead to contamination and serious accidents. Their use is forbidden.
使用将一种气体瓶阀转换成另一种气体瓶阀的接头，会导致气体污染和严重事故，严禁使用。
16.
Position sensor to throttle body while guiding rubber fitting over throttle body vacuum nipple.
在节气阀体真空管接头上面操纵橡胶管件时，定位感知器至节气阀体。
17.
"This allows interchangeability of gear operators, actuators, and adapter bushings from valve mounting flange to extension stem top flange."
因此,蜗轮操作装置、驱动装置和衬套接头可以从阀门安装法兰上替换到阀杆延长件顶部法兰上。
18.
Install a listed temperature-pressure relieve valve in the remaining fitting.
在剩下的螺纹接头上安装额定温度/水压的安全阀。