1.
Carbon emission pinch analysis for energy planning in chemical industrial park
碳夹点分析技术与化工园区能源规划
2.
The Slab Quality Analysis of Ultra-low-carbon Steel at FTSC in BX-Steel
本钢FTSC生产超低碳钢的铸坯夹杂物的分析
3.
Aiming at the character of modular fixture design, the configuration of modular fixture is analyzed in detail and researched in this paper.
针对组合夹具设计的特点,全面分析和研究了组合夹具的结构。
4.
Analysis of the new characteristics of Korean foreign policy in the 21the century;
夹缝中求生存——21世纪朝鲜外交政策新特点分析
5.
Pinch analysis on the heat exchanger network of the triethylene glycol(TEG) dehydration unit in gas purification plants
三甘醇脱水装置换热网络夹点技术分析
6.
Fault Analysis of Wire Clip Heating in Neutral Point Loop of Main Transformer
主变中性点回路线夹发热引起的故障分析
7.
Finite Element Analysis on the Bending Behavior of Point-supported Laminated Glass Panel
点支式夹层玻璃板受弯承载性能的有限元分析
8.
VIBRATION CHARACTERISTICS AND OPTIMIZATION OF TRUSS-CORED METAL SANDWICH PLATES
点阵多孔金属夹芯板振动特性分析及优化设计
9.
The present paper analyzes the difficult points in refining the high carbon steel by converter and describes its operating essentials, which include good control of the carbon temperature and properly slagging for dephosphorization purpose.
分析了转炉冶炼高碳钢的难点，探讨了转炉冶炼高碳钢的操作要点：控制好碳温、好造渣脱磷操作。
10.
Comparative Research about Methods of Strengthening Joints of Frame by Enlarging Column Section, Bonding Steel Plates and Bonding CFRP;
柱加大截面、粘钢、碳纤维加固框架节点对比分析
11.
Cause analysis of unobvious yield point of low carbon steel hot-rolled wire rod
低碳钢热轧盘条屈服点不明显的原因分析
12.
A new algorithm of endpoint carbon content of BOF based on of off-gas analysis
基于烟气分析转炉终点碳含量控制的新算法
13.
THERMODYNAMIC ANALYSIS ON FORMATION AND TRANSFORMATION OF GLOBULAR INCLUSIONS IN CaSi TREATED BEARING STEEL
轴承钢钙处理时点状夹杂物生成及转变的热力学分析
14.
Analysis of Clinical Characteristics and Surgical Treatment on 38 Cases of Stanford Type A Aortic Dissection
38例Stanford A型主动脉夹层的临床特点和手术治疗分析
15.
Analysis on Effect of MgO Content to the Melting Point of Refinery Slag and Inclusions in Pipeline Steel
MgO含量对管线钢中精炼渣和夹杂物熔点影响分析
16.
Finite Element Analysis of Multi-point Clamping Scheme Effect on Milling Deformation of Multi-frame Components
多点装夹方案对多框体铣削变形影响的有限元分析
17.
ELASTIC-PLASTIC DYNAMIC RESPONSE ANALYSIS OF SANDWICH BEAMS WITH LATTICE TRUSS CORES BASED ON MINIMUM PRINCIPLE OF ACCELERATION
基于最小加速度原理分析点阵材料夹芯梁的弹塑性动力响应
18.
A Study on Development of Detecting and Analyzing System for Ms Temperature in the HAZs of Carbon Structural Steels;
碳素结构钢焊接热影响区组织Ms点测试分析系统的研究与开发