1) composite pore former
复合造孔剂
2) resin microbead
复合致孔剂
3) compound fluxing agent
复合造渣剂
1.
A new type compound fluxing agent pill has been manufactured which is used during BOF steelmaking with semi-steel.
研究了攀钢转炉污泥特性和利用率现状,研制出了用于半钢转炉冶炼的新型复合造渣剂,分析了新型复合造渣剂对转炉终点氧化性、溅渣护炉、钢铁料消耗以及转炉脱P效果的影响,拓展了转炉污泥的使用途径;使攀钢除尘资源得到了较好的循环经济利用,减轻了环保的压力。
4) pore-forming agent
造孔剂
1.
Effect of pore-forming agents content on bending strength of SiC/Al composites;
造孔剂含量对SiC/Al复合材料抗弯强度的影响
2.
Effect of pore-forming agents on mechanical properties of metal-bonded diamond wheels
造孔剂对金属结合剂金刚石磨具力学性能的影响
3.
In this paper, the porous silica ceramic materials and parts are fabricated by introducing the pore-forming agents into the materials by pelletizing method, aging the slip in the vacuum conditions and casting the slip under pressure.
通过造粒的方法引入造孔剂,采用真空抽气混合料浆及加压浇注的方法来制备多孔石英陶瓷材料及其部件。
5) pore former
造孔剂
1.
Effect of the pore former on the performance of air electrode;
造孔剂对空气电极电性能的影响
2.
The effect of mechanics of different pore former on the properties of low weight high insulation sintering product
不同成孔机理造孔剂对轻质保温烧结制品性能的影响
3.
The porous SiC ceramics were prepared by vacuum sintering in this investigation,the effect of different sintering aids,Al2O3-Y2O3 and Si,and different pore formers,acrylamide copolymer and Carboxymethyl Cellulose(CMC) on the microstructures and porosity were studied.
采用真空烧结方法制备了SiC多孔陶瓷,研究了不同助烧结剂Al2O3-Y2O3、Si以及不同造孔剂丙烯酰胺聚合物、羧甲基纤维素(CMC)对SiC多孔陶瓷形貌和气孔率的影响。
6) pore forming agent
造孔剂
1.
Influence of pore forming agents on the performance of membrane electrode assembly in PEMFC;
造孔剂对PEMFC膜电极性能的影响
2.
High specific surface area silicon carbide(SiC) was synthesized using citric acid(CA) as the pore forming agent by the tetraethoxysilane (TEOS) sol-gel and carbothermal method.
以柠檬酸为造孔剂,利用硅酸乙酯溶胶-凝胶和碳热还原法制备出了高比表面积的纳米碳化硅(SiC)粉体。
3.
In this experiment,diatomite and pore forming agent are used as main materials,half dry press mold,general sintering,a series cost-effective porous ceramics were produced.
本实验以硅藻土为主要原料 ,天然有机细粉为造孔剂 ,水玻璃为高温粘合剂 ,经半干压成型 ,常规烧成 ,制出了性能优良的硅藻土多孔陶瓷 ,随着造孔剂的加入量、烧成制度的改变 ,气孔率从 47%增加至 71 % ,最大孔径也随之从 1～ 1 0 μm变化 ,密度从 1 。
补充资料：复合固体推进剂氧化剂
分子式：
CAS号：
性质：它提供推进剂自持燃烧所需的氧。要求氧化剂的有效氧含量高、密度大、生成热高、分解产物为气体、安定性好，与推进剂组分化学相容。氧化剂品种、含量、颗粒形状、粒度及粒度分布对推进剂的能量、燃烧、力学、工艺、安全等性能有重要影响。在推进剂中用量一般占60％～75％，常用的氧化剂有高氯酸铵、硝酸铵、奥克特今、黑索今等。
CAS号：
性质：它提供推进剂自持燃烧所需的氧。要求氧化剂的有效氧含量高、密度大、生成热高、分解产物为气体、安定性好，与推进剂组分化学相容。氧化剂品种、含量、颗粒形状、粒度及粒度分布对推进剂的能量、燃烧、力学、工艺、安全等性能有重要影响。在推进剂中用量一般占60％～75％，常用的氧化剂有高氯酸铵、硝酸铵、奥克特今、黑索今等。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条